Husqvarna GTH26V48LS To Move Forward and Backward See Fig, To USE Cruise Control J See Fig

Page 10

OPERATION

TO MOVE FORWARD AND BACKWARD (See Fig. 7)

The direction and speed of movement is controlled by the forward and reverse drive pedals.

•Start tractor and release parking brake.

•Slowly depress forward (K) or reverse (L) drive pedal to begin movement. Ground speed increases the further down the pedal is depressed.

K

J

L

Fig. 7

TO USE CRUISE CONTROL (J) (See Fig. 7)

The cruise control feature can be used for forward travel only.

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

•With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

A

Fig. 8

•Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in this section of manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

Fig. 9

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitat- ing or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut (see "TO ADJUST MOWER CUTTING HEIGHT")

•Start mower blades by engaging attachment clutch control.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents GTH26V48LS General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts AssemblyTools Required for Assembly ToremovetractorfromcartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor To SET Parking Brake See Fig HOW to USE Your TractorAttachment Clutch Switch Disengaged Engaged Stopping See FigTo Move Forward and Backward See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To USE Cruise Control J See FigReverse Operation System ROS See Fig Using the Reverse Operation SystemTo Stop Mower Blades To Operate on HillsCheck Engine OIL Level Service REMINDER/HOUR MeterBefore Starting the Engine ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP General Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigEngine IN-LINE Fuel Filter See Fig CleaningDeck Washout Port See Fig To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Figs O PRaise attachment lift lever to highest position To Level Mower To Replace Mower Blade Drive Belt To Check BrakeFront Wheel TOE-IN/CAMBER Belt InstallationTo Replace Motion Drive Belt See Fig To Remove Wheel for Repairs See FigReplacing Battery See Fig To Start Engine with a Weak Battery see FIGTo Remove CABLES, Reverse Order Transmission Fuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine continues KEY Part Description DecalsWheels and Tires KEY Part NO. NO. DescriptionSchematic SCH12Electrical KEY Part Description Chassis Tractor Model NO. GTH26V48LS 96043009000, Product no 43 Drive G7-BCBB-1XDC-1FCA Engine Engine Power Rating Information Steering Assembly Tractor Model NO. GTH26V48LS 96043009000, Product no 43 Seat Assembly Mower Lift   Mower Deck Tractor Model NO. GTH26V48LS 96043009000, Product no 43 Service Notes Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX12.15.09 BAD

GTH26V48LS specifications

Husqvarna GTH26V48LS is a powerful and reliable lawn tractor designed for homeowners looking for efficiency and comfort in lawn care. With its robust engine and advanced features, it aims to make the mowing experience smoother and more enjoyable.

One of the standout characteristics of the GTH26V48LS is its 26 HP Kohler engine, which provides ample power for cutting through tough grass and tackling uneven terrains. The engine is designed to deliver both power and fuel efficiency, ensuring that homeowners can tend to their lawns without frequently worrying about refueling.

The cutting deck of the Husqvarna GTH26V48LS is 48 inches wide, allowing for a wider cutting path and efficient mowing of larger areas. This deck is equipped with three blades that provide a clean and precise cut, coupled with an adjustable cutting height ranging from 1 to 4 inches. Users can easily customize their mowing height to suit the grass type and personal preference.

Another significant feature is the pedal-operated hydrostatic transmission, which offers an easy and smooth driving experience. This system allows for effortless speed control without the need for shifting gears, making it an excellent choice for those who may be less experienced with lawn tractors. Coupled with the ergonomic steering wheel, the overall operation is designed for comfort during prolonged mowing sessions.

The Husqvarna GTH26V48LS also incorporates advanced technologies such as the SmartSwitch electrical control system, which simplifies starting and operation. This technology ensures a reliable starting process while minimizing potential issues down the line.

Additionally, the tractor features a comfortable high-back seat that provides support during longer mowing sessions. The front headlights enhance visibility while mowing in low light conditions, making it practical for early morning or late evening tasks.

Overall, the Husqvarna GTH26V48LS combines power, efficiency, and comfort, making it an ideal choice for homeowners seeking a robust lawn tractor that can handle various lawn care needs.
Top Page Image Contents