Husqvarna GTH2548 To Adjust Gauge Wheels See Fig, To Operate Mower See Fig, To Operate on Hills

Page 13

OPERATION

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

Remove retainer spring and clevis pin which secure each gauge wheel bar.

Lower gauge wheels to ground. Raise gauge wheels slightly to align holes in bracket and gauge wheel bar and insert clevis pin. Gauge wheels should be slightly off the ground.

Replace retainer spring into clevis pin.

Be sure all gauge wheels are in the same setting.

IMPORTANT:BE SURETO READJUST GAUGEWHEELS IFYOU CHANGE THE CUTTING HEIGHT OF THE MOWER DECK.

RETAINER

01977

SPRING

 

CLEVIS

PIN

FIG. 9

TO OPERATE MOWER (See Fig. 10)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

Select desired height of cut.

Lower mower with attachment lift control.

Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield in place.

ATTACHMENT CLUTCH

LIFT LEVER

HIGEST PO-

SWITCH PULL OUT TO

SITION

“ENGAGE”

 

 

LOWEST

 

POSITION

PUSH IN TO

DEFLECTOR

“DISENGAGE”

SHIELD

 

 

02142

TO OPERATE ON HILLS

WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

Choose the slowest speed before starting up or down hills.

Avoid stopping or changing speed on hills.

If stopping is absolutely necessary, push brake pedal quickly to brake position and engage parking brake.

IMPORTANT: THE MOTION CONTROL LEVER RETURNS TO NEUTRAL (N) POSITION WHEN THE BRAKE PEDAL IS FULLY DEPRESSED.

To restart movement, slowly release parking brake and brake pedal.

Slowly move motion control lever to slowest setting.

Make all turns slowly.

TO TRANSPORT (See Figs. 7 and 11)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor.

Raise attachment lift to highest position with attachment lift control.

Pull freewheel control out and into the slot and release so it is held in the disengaged position.

Do not push or tow tractor at more than two (2) MPH.

To reengage transmission, reverse above procedure.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

02219

FIG. 11

TOWING CARTS AND OTHER ATTACH- MENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your trac- tor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

FIG. 10

13

Image 13
Contents GTH2548 Safe Operation Practices for RIDE-ON Mowers IV. ServiceGeneral Operation II. Slope OperationSafety Rules Table of Contents Unassembled Parts Assembly Assemble Gauge Wheels to Mower Deck See Fig To Attach Nose Roller See FigInstall Mower and Drive Belt See Figs Check Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigPurge Transmission Mowing TipsGeneral Recommendations MaintenanceBefore Each USE Tractor Engine Cleaning To Install Mower Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Secondary Drive Belt See Fig To Replace Mower Drive BeltTo Check and Adjust Brake To Adjust Attachment Clutch See FigTo Replace Motion Drive Belt See Fig Transmission REMOVAL/REPLACEMENT Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERReplacing Battery See Fig To Start Engine with a Weak Battery See FigTo Attach Jumper Cables To Remove CABLES, Reverse OrderTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILTroubleshooting Points With attachment clutch Service Notes Tractor Model NO. GTH2548 GTH2548A, Product no 57 SchematicElectrical KEY Part Description 138 Chassis and EnclosuresRepair Parts 153 Ground DriveTransaxle Hydro Gear Steering Assembly Repair Parts Spark Arrester KIT KEY Part Description EngineLift Assembly 532 18 Seat Seat AssemblyWheels & Tires DecalsMower Decb Mower Deck Warranty Statement Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation532 18 99-42 Rev 5.25.04 TR/MH