Husqvarna GTH2548 owner manual Transaxle Motion Control Lever Neutral Adjustment See Fig

Page 24

SERVICE AND ADJUSTMENTS

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 27)

The motion control lever has been preset at the factory and adjustment should not be necessary.

•Park tractor on level surface. Stop tractor by turning ignition key to “OFF” position and engage parking brake.

•Loosen the adjustment bolt in front of the right rear wheel.

•Move motion control lever to the neutral position (N).

•Tighten the adjustment bolt.

02508

ADJUSTMENT

BOLT

FIG. 27

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See“PURGETRANSMISSION” in the Operation section of this manual.

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS

FRONT WHEEL (See Fig. 28)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal.

•Repair tire and reassemble.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

REAR WHEEL -

•Block rear axle securely.

•Remove five (5) hub bolts to allow wheel removal.

•Repair tire and reassemble. Replace and tighten hub bolts securely.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING RING

AXLE

COVER

sq 3 0066

FIG. 28

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents GTH2548 IV. Service Safe Operation Practices for RIDE-ON MowersGeneral Operation II. Slope OperationSafety Rules Table of Contents Unassembled Parts Assembly To Attach Nose Roller See Fig Assemble Gauge Wheels to Mower Deck See FigInstall Mower and Drive Belt See Figs Check Tire Pressure Check Mower LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Purge TransmissionMaintenance General RecommendationsBefore Each USE Tractor Engine Cleaning Service and Adjustments To Install MowerTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Drive Belt To Replace Mower Blade Secondary Drive Belt See FigTo Adjust Attachment Clutch See Fig To Check and Adjust BrakeTo Replace Motion Drive Belt See Fig Transaxle Motion Control Lever Neutral Adjustment See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Start Engine with a Weak Battery See Fig Replacing Battery See FigTo Attach Jumper Cables To Remove CABLES, Reverse OrderTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points With attachment clutch Service Notes Schematic Tractor Model NO. GTH2548 GTH2548A, Product no 57Electrical KEY Part Description Chassis and Enclosures 138Repair Parts Ground Drive 153Transaxle Hydro Gear Steering Assembly Repair Parts Engine Spark Arrester KIT KEY Part DescriptionLift Assembly Seat Assembly 532 18 SeatDecals Wheels & TiresMower Decb Mower Deck Warranty Statement Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX532 18 99-42 Rev 5.25.04 TR/MH
Top Page Image Contents