Husqvarna GTH225 owner manual Tools Required for Assembly, To Remove Tractor from Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

Tire pressure gauge

 

(2)

9/16" wrenches

(1) Utility knife

(1)

1/2" wrench

(1) 3/4" socket w/drive ratchet

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut, from top to bottom, along lines on all four corners of carton, and lay panels flat.

•Remove mower and packing materials.

•Check for any additional loose parts or cartons and remove.

BEFORE ROLLING TRACTOR OFF SKID

ATTACH STEERING WHEEL (See Fig. 1)

•Remove hex bolt, lock washer and large flat washer from steering shaft.

•Position front wheels of the tractor so they are pointing straight forward.

STEERING WHEEL

INSERT

HEX BOLT

LOCKWASHER

FLAT WASHER

STEERING

WHEEL

STEERING

SHAFT

STEERING

WHEEL

ADAPTER

•Position steering wheel so cross bars are horizontal (left to right) and slide onto adapter.

•Secure steering wheel to steering shaft with hex bolt, lock washer and large flat washer previously removed. Tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

HOW TO SET UP YOUR TRACTOR

CHECK BATTERY (See Fig. 2)

•Lift hood to raised position.

•If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in CUSTOMER RESPONSIBILITIES section of this manual for charging instructions).

LABEL

FIG. 2

FIG. 1

INSTALL SEAT (See Fig. 3)

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard packing. Remove cardboard packing and discard.

•Place seat on seat pan and assemble shoulder bolt. Tighten shoulder bolt securely.

•Assemble adjustment knob and flat washer loosely. Do not tighten.

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely.

SEAT

SEAT PAN

SHOULDER

BOLT

ADJUSTMENT

KNOB

FLAT

WASHER

FIG. 3

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents GTH225 Safety Rules Safe Operation Practices for Ride-On MowersBecome ALERT!!! Your Safety is IN- Volved Table of Contents Contents of Hardware Pack HOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonTo Attach Front Bumper See Fig To Attach Nose Roller See FigAssemble Gauge Wheels to Mower Deck See Fig Install Mower and Drive Belt See Figs To SET UP Your Mower for Mulching See FigTo Install Mulcher Plate See Fig To Convert to Bagging or DischargingCheck for Proper Position of ALL Belts Check Tire PressureCheck Mower Levelness Check Brake System3CHECKLIST Operation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Operate Mower See FigTo Operate on Hills Towing Carts and Other AttachmentsADD Gasoline Before Starting the EngineCheck Engine OIL Level See Fig To Start Engine See FigMowing Tips Purge TransmissionMulching Mowing Tips General Recommendations Lubrication ChartCustomer Responsibilities Before Each USETractor Engine Muffler CleaningEngine OIL Filter Spark PlugsTo Level Mower Housing Service and AdjustmentsTo Install Mower To Remove Mower See FigTo Replace Mower Drive Belt To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt To Adjust Attachment Clutch See FigTo Adjust Brake See Fig See FigFront Wheel TOE-IN Adjustment Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment Front Wheel CamberTo Replace Headlight Bulb Interlocks and RelaysTo Replace Fuse To Adjust Choke Control See Figs To Remove Hood and Grill Assembly See FigTo Adjust Throttle Control Cable See Fig To Adjust Carburetor See FigFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionOFF Schematic Engine Connector Tractor ConnectorElectrical KEY Part Description Chassis and Enclosures Repair Parts Ground Drive KEY Part NO. NO. Description Steering Assembly Adapter, Wheel Steering Engine Spark Arrester KITSeat Assembly Decals Wheels & TiresLift Assembly 532171211 Retainer, SpringMower Deck Repair Parts Suggested Guide for Sighting Slopes for Safe Operation Sighting GuideWarranty Statement Limited WarrantyRev 10.27.99 JH/TR/JH

GTH225 specifications

The Husqvarna GTH225 is a standout riding mower designed for those who seek a blend of performance, comfort, and reliability in lawn care. Engineered for durability and versatility, this model is perfect for homeowners who manage medium to large yards.

At the heart of the GTH225 is a robust and efficient engine. Powered by a 22 HP Kohler engine, it delivers consistent performance for cutting even the toughest grass. The engine is designed to ensure smooth operation and offers the torque needed for impressive cutting power. Additionally, the hydrostatic transmission allows for seamless speed adjustments, providing an easy and responsive driving experience.

One of the key features of the Husqvarna GTH225 is its cutting deck, which spans a wide 48 inches. This substantial deck size means fewer passes are required to cover large areas, making lawn maintenance quicker and more efficient. The cutting height can be adjusted from 1.5 to 4 inches, catering to different grass types and seasonal growth patterns. The deck is also equipped with high-quality blades, which provide clean cuts and a professional finish.

Comfort is a major consideration with the GTH225. The operator's seat is well-cushioned and ergonomically designed, enabling users to mow for extended periods without discomfort. The steering wheel and controls are intuitively placed, ensuring that operation is user-friendly and requires minimal effort.

The Husqvarna GTH225 is also built to enhance maneuverability. With a tight turning radius, it easily navigates around obstacles like trees and flower beds. This agility is complemented by its durable construction, featuring a sturdy frame that can withstand the rigors of regular use.

Another innovative feature is the optional mulching kit, which enhances the mower's versatility. It allows for superior grass recycling, thereby enriching the lawn without the need for bagging clippings. Additionally, the model can be equipped with a tow hitch for added functionality, enabling users to attach various gardening tools or trailers.

In line with Husqvarna’s commitment to environmental sustainability, the GTH225 is designed with fuel efficiency in mind, helping homeowners reduce their carbon footprint while keeping their lawns pristine. Overall, the Husqvarna GTH225 combines advanced technology, comfort, and performance, making it a reliable choice for anyone serious about maintaining their outdoor space.
Top Page Image Contents