Husqvarna iZ4821KAA, iZ5223KAA, iZ5223KOA, iZ4217SKAA, iZ4817SKAA, iZ4817KAA, iZ6123KAA manual

Page 16

SETUP AND ADJUSTMENTS

Park Brake Adjustment

For Models: 968999206, 968999207,

968999208, 968999231,

968999235

1.Stop engine and remove key. Release park brake and measure the length of the spring. The distance between the washer on each end of the spring should be 2-7/8". FIG - 5

2.If adjustment is needed, loosen the nut below the spring. Then rotate nut to desired position so the proper distance between the washers is obtained. Check other side for proper adjust- ment.

3.Engage the brake lever and measure the distance between the trunnion pin and the collar welded to the brake rod. Distance should be 3/ 16" to 1/4". FIG - 5

4.If adjustment is needed, loosen the lock nut directly below the yoke. Using a wrench, rotate the rod by turning the double nuts using the nuts below the yoke and the nut you just loosened, to obtain the 3/16" to 1/4" distance. Tighten nut against yoke and check other side for proper adjustment.

FIG - 5

Park Brake Adjustment

For Models: 968999229, 968999230

1.Stop engine and remove key, release park brake and check the gap between the rear tire and the brake arm. The gap should be 1/8” to 1/4”.

2.If adjustment is needed, loosen the lock nut next to the yoke. Remove the pin from the front yoke so you can rotate the yoke on the adjust- ment link until the proper gap is achieved.

3.Make sure the brake arm on both sides does not touch the tire when the brake is in the off position. FIG - 6

FIG - 6

Motion Control Linkage Adjustment

This adjustment must be made with the rear wheels rotating. Raise the rear of the machine and block it up so the wheels are free to rotate.

CAUTION: Keep hands, feet and clothing away from rotating tires.

Tilt seat forward and remove the seat rod so the seat may rotate forward onto the frame.

Place a 2x4 board between the foot plate and the center of the seat to engage the seat safety switch.

Loosen the nuts directly behind each ball joint on both rods that connect the pump arm to the motion control assemblies. FIG - 7

Start the engine. The park brake must be en- gaged and the motion control levers in the neutral slots to start the engine. Run the engine approximately half throttle

Release park brake to allow the wheels to rotate.

16

Image 16
Contents Operators manual Manual no REV. IR 09/01/03Husqvarna. All right reserved Beatrice, NE. Printed U.S.A Contents Introduction IntroductionGood Service Symbols and Decals Symbols and DecalsSafety Instructions Safety InstructionsGeneral Use Keep children away from the work area Driving on Slopes Do as followsMaintenance Children8011-563 Transport Important InformationPresentation PresentationSetup and Adjustments SetupAdjustments Cutting HeightMower Deck Leveling Throttle Lever TensionPark Brake Adjustment For Models 968999229 Motion Control Linkage AdjustmentOperation Operating instructionsStarting and operation ControlsSpin very rapidly if one lever is positioned When using this maneuver the machine canTo far ahead of the other Maintenance Safety interlock systemCutter Housings Engine oilHardware Air filterHydraulic system Deck beltPump belt LubricationTire pressure Caster WheelsTorque Specifications Maintenance Schedule Trouble Shooting ProblemWiring Diagrams Console Harness Schematic Harness Frame Frame Harness

iZ4821KAA, iZ5223KAA, iZ5223KOA, iZ4217SKAA, iZ4817 SKAA, iZ4817KAA, iZ6123KAA, iZ4821KAA, iZ5223KAA, iZ5223KOA, iZ4217SKAA, iZ4817SKAA, iZ4817KAA, iZ6123KAA specifications

Husqvarna has long been synonymous with quality outdoor equipment, particularly in the realm of zero-turn mowers. Among their extensive lineup, models like the iZ4821KAA, iZ5223KAA, iZ5223KOA, iZ4217SKAA, iZ4817SKAA, iZ4817KAA, and iZ6123KAA stand out for their superior performance and innovative features.

Starting with the iZ4821KAA, this model is equipped with a robust 21 horsepower engine, ensuring reliable power for tackling even the most challenging mowing tasks. Its 48-inch cutting deck allows for efficient navigation around obstacles, while the zero-turn capability enables sharp turns for precise trimming.

Next, the iZ5223KAA boasts a larger 23-horsepower engine and a 52-inch cutting deck, making it suitable for larger properties. The commercial-grade construction provides durability and longevity, while features such as electric blade engagement and a high-back seat enhance user comfort during lengthy mowing sessions.

The iZ5223KOA combines performance and advanced features, including a hydraulic system for improved maneuverability. Its adjustable cutting height provides versatility in maintaining lawns of varying grass lengths.

For those looking for a compact mower, the iZ4217SKAA offers a 17-horsepower engine with a 42-inch deck, perfect for small to medium-sized yards. Its lightweight design and agile handling make it an excellent choice for homeowners seeking efficiency without sacrificing performance.

The iZ4817SKAA and iZ4817KAA both feature a 17-horsepower engine, delivering robust power with a 48-inch cutting deck. These models are designed with user-friendly controls and a comfortable seating position, making them easy to operate for anyone.

Finally, the iZ6123KAA represents the pinnacle of Husqvarna's engineering, featuring a 23-horsepower engine and a 61-inch deck, ideal for commercial use or larger properties. Its innovative technology includes a dual hydrostatic transmission for smooth power delivery and enhanced maneuverability, while built-in safety features ensure a secure mowing experience.

Collectively, these models integrate technologies such as high-capacity air filtration systems, optimized engine cooling, and a user-friendly dashboard with intuitive controls. Each model promises efficiency, comfort, and durability, solidifying Husqvarna's reputation as a leader in power equipment. Whether for residential use or commercial applications, these zero-turn mowers cater to a variety of needs, ensuring a well-maintained lawn with ease and precision.