Husqvarna YTH2448T To Start Engine See Fig, Purge Transmission, Automatic Transmission Warm UP

Page 12

OPERATION

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE (See Fig. 3)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

•Be sure freewheel control is in the transmission engaged position.

•Sit on seat in operating position, depress brake pedal and set parking brake.

•Move attachment clutch to “DISENGAGED” position.

•Move throttle control to fast position

•Pull choke control out for a cold engine start attempt. For a warm engine start attempt the choke control may not be needed.

NOTE: Before starting, read the warm and cold starting procedures below.

•Insert key into ignition and turn key clockwise to “START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, push choke control in, wait a few minutes and try again. If engine still does not start, pull the choke control out and retry.

WARM WEATHER STARTING (50° F and above)

•When engine starts, slowly push choke control in until the engine begins to run smoothly. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING (50° F and below)

•When engine starts, slowly push choke control in until the engine begins to run smoothly. Continue to push the choke control in small steps allowing the engine to accept small changes in speed and load, until the choke control is fully in. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

AUTOMATIC TRANSMISSION WARM UP

•Before driving the unit in cold weather, the transmission should be warmed up as follows:

•Be sure the tractor is on level ground.

•Release the parking brake and let the brake slowly return to operating position.

•Allow one minute for transmission to warm up.This can be done during the engine warm up period.

•The attachments can be used during the engine warm-up period after the transmission has been warmed up and may require the choke control be pulled out slightly.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

PURGE TRANSMISSION

CAUTION: Never engage or disengage freewheel lever while the engine is run-

ning.

To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have de- veloped during shipping of your tractor.

IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD BE PURGED AFTER REINSTALLATION BEFORE OPERATING THE TRACTOR.

•Place tractor safely on level surface with engine off and parking brake set.

•Disengage transmission by placing freewheel control in freewheeling position (See “TO TRANSPORT” in this section of manual).

•Sitting in the tractor seat, start engine. After the engine is running, move throttle control to slow position. Dis- engage parking brake

•Depress forward drive pedal to full forward position, hold for five (5) seconds and release pedal. Depress reverse drive pedal to full reverse position, hold for five

(5) seconds and release pedal. Repeat this procedure three (3) times.

NOTE: During this procedure there will be no movement of drive wheels. The air is being removed from hydraulic drive system.

•Shut- off engine and set parking brake.

•Engage transmission by placing freewheel control in engaged position (See “TO TRANSPORT” in this sec- tion of manual).

•Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. Disengage parking brake.

•Drive tractor forward for approximately five feet then backwards for five feet. Repeat this driving procedure three times.

Your transmission is now purged and now ready for normal operation.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents 917.279200 Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService III. ChildrenIV. Towing Table of Contents Assembly Unassembled PartsTo Remove Tractor from Carton Unpack CartonCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor Reverse Operation System ROS on PositionHOW to USE Your Tractor StoppingTo Adjust Mower Cutting Height See Fig To Adjust Gauge Wheels See FigSystem Characteristics To Operate MowerService REMINDER/HOUR Meter Before Starting the EngineTo Operate on Hills Check Engine OIL LevelTo Start Engine See Fig Purge TransmissionAutomatic Transmission Warm UP Mowing Tips Maintenance Before Each USEBattery TractorBrake Operation TiresEngine Service and Adjustments CleaningIN-LINE Fuel Filter See Fig Tractor See FigTo Install Mower See Figs First Install ANTI-SWAY BAR SEH J To Level Mower Mower Drive Belt Installation To Replace Mower Blade Drive Belt See FigMower Drive Belt Removal To Replace Motion Drive Belt See Fig To Check BrakeFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTo Start Engine with a Weak Battery See Fig Replacing Battery See FigTo Attach Jumper Cables To Remove CABLES, Reverse OrderTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Engine dies when Service Notes Schematic Tractor Model no .279200 YTH2448TElectrical KEY Part NO. NO.DESCRIPTION Chassis KEY Part Description Drive KEY Part NO. NO.DESCRIPTION Steering Assembly Spark Arrester KIT EngineSeat Assembly Decals Wheels and TiresMower Deck KEY Part NO. NO.DESCRIPTION Mower Lift Service Notes Repair Parts Key Part Description Briggs Engine Model Number 445677, Type Number 0413-E1 Emission Label Label KITCarburetor Gasket SET Replacement Engine KEY Part Description KEY Part Description Suggested Guide for Sighting Slopes for Safe Operation Warranty Statement

YTH2448T specifications

The Husqvarna YTH2448T is a robust and reliable riding lawn mower designed for homeowners who wish to maintain their lawns efficiently and effortlessly. Combining modern technology with user-friendly design, this mower delivers impressive performance while ensuring comfort during extended use.

One of the standout features of the YTH2448T is its powerful 24 HP Briggs & Stratton Intek engine. This engine provides ample power for tackling various lawn conditions, ensuring that the mower can handle tall grass and rugged terrain without sacrificing performance. The engine also features an automatic choke system, making it easy to start even in cold temperatures.

Equipped with a 48-inch cutting deck, the YTH2448T offers a wide cutting path, allowing users to cover more ground in less time. The deck is made from high-quality materials to ensure durability and is designed with a reinforced cutting edge to prevent wear and tear. Additionally, the deck features an adjustable cutting height, allowing users to choose the optimal height for their lawn.

The mower also incorporates an innovative hydrostatic transmission system that provides seamless acceleration and speed control. This technology eliminates the need for shifting gears, making it easier for users to navigate their lawns with precision. The YTH2448T also boasts a tight turning radius, allowing for maneuverability around obstacles such as trees and flower beds.

Comfort is prioritized in the design of the YTH2448T. The mower features an ergonomic seating position with an adjustable seat to accommodate various user heights. The controls are intuitively placed within easy reach, allowing operators to focus on mowing without distraction. The mower is also equipped with a built-in cup holder, providing convenience for long mowing sessions.

Another impressive characteristic of the Husqvarna YTH2448T is its low vibration design, which enhances comfort and reduces fatigue during use. The mower's construction also includes sound damping technology, resulting in a quieter operation, making it suitable for residential neighborhoods.

In conclusion, the Husqvarna YTH2448T is an exceptional riding lawn mower that combines power, comfort, and efficiency. With its reliable engine, wide cutting deck, advanced transmission, and user-friendly features, it stands out as an ideal choice for homeowners looking to keep their lawns in pristine condition. Whether you are a seasoned lawn care enthusiast or a novice, the YTH2448T promises to make lawn maintenance a breeze.
Top Page Image Contents