Husqvarna YTH23V48 owner manual Chassis

Page 33

TRACTOR - MODEL NO. YTH23V48 (96048001000), PRODUCT NO. 960 48 00-10

CHASSIS

KEY	PART
NO.	NO.	DESCRIPTION
3	532 43 97-52	Logo
5	532 43 74-71	Dash
14	532 43 97-25	Hood
15	532 43 97-33	Lens LH
18	532 43 77-62	Grille Asm.
25	532 43 97-32	Lens RH
34	532 19 61-25	Plate Engine
36	817 06 05-12 Screw 5/16-18 x 3/4
37	532 42 36-94	Fender
52	873 68 05-00 Nut Lock 5/16-18
68	817 49 05-08 Screw 5/16-18 x 1/2
130	532 41 63-58 Screw #10 x 0.750 BOS Thread
137	532 40 75-90	Bumper Dash
150	532 43 97-74	Air Duct
151	532 43 66-70 Pivot Bracket Hood
152	532 19 95-35	Shield Browning
161	532 43 97-81	Window Fuel
162	532 14 24-32	Screw
165	532 19 68-26 Support Tank Rear
175	532 19 63-04	Crossmember

176532 40 07-76 Screw 10-24 x 5/8

177532 19 52-27 Bushing Steering

180	532 19 54-57	Chassis
182	532 40 68-59	Dash Lower
183	874 52 05-20	Bolt 5/16-18 x 1-1/4 Full. Thd.
189	817 00 05-12	Screw 5/16-18 x 3/4
191	532 43 74-55	Insert Reflective RH
194	873 90 05-00	Nut Lock Hex Flange 5/16-18

KEY	PART
NO.	NO.	DESCRIPTION
195	532 40 41-37	Plug Hole Dash Lower
199	532 41 34-85	Plate Deck Lift

202532 43 97-28 Vent Side Hood RH

203532 43 97-27 Vent Side Hood LH

204 532 43 57-14 Vent Top Hood

205532 43 97-30 Skirt Hood Side RH

206532 43 97-29 Skirt Hood Side LH

207	532 43 97-34	Bezel RH
208	532 43 97-35	Bezel LH

213874 76 05-12 Bolt 5/16-18 unc x 3/4

214532 19 91-45 Clip Retainer Tinner

217	532 40 91-67	Rod Pivot
218	532 19 63-95	X-Piece Hood Stop
228	532 19 51-61	Stud Fastner
233	532 19 65-39	Bolt, Shoulder
235	532 40 61-29	Spacer Fender
236	873 93 05-00	Nut Lock 5/16-18 unc

282532 41 41-10 Clip Retainer Console

283532 43 96-83 Console Asm. Decklift

284 532 43 91-50 Console Asm.

285532 41 63-15 Console Insert RH

286532 41 63-17 Console Insert LH

287817 60 04-06 Screw Hex Washead 1/4-20 x 3/8

297	532 43 74-56	Insert Reflective LH
- -	532 43 18-83	Kit Bumper

NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm

33

Image 33

Contents YTH23V48 Safe Operation Practices for Ride-On Mowers General OperationII. Slope Operation General Service ServiceIII. Children IV. TowingTable of Contents Toremovetractorfromcarton Tools Required for AssemblyBefore Removing Tractor from Skid Unpack CartonCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor To SET Parking Brake See Fig HOW to USE Your TractorStopping See Fig To USE Throttle Control D See FigTo Stop Mower Blades To Operate MowerUsing the Reverse Operation System Service REMINDER/HOUR MeterReverse Operation System ROS To Operate on HillsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigPurge Transmission Mowing TipsLubrication Chart MaintenanceGeneral Recommendations ScheduleTractor BatteryBlade Care Blade Removal See FigEngine Muffler CleaningIN-LINE Fuel Filter See Fig Deck Washout Port See FigTo Remove Mower See Fig To Install Mower See FigsTurn Steering Wheel Left and Position Mower See Fig ANTI-SWAY BAR SAttach Mower Side Suspension Arms a to Chassis See Fig To Replace Mower Blade Drive Belt See Fig Mower Drive Belt InstallationTo Check Brake To Level MowerBelt Installation To Replace Motion Drive Belt See FigBelt Removal To Remove Wheel See Fig To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Attach Jumper CablesTransmission Fuel System OtherEngine OIL CylindersProblem Cause Correction TroubleshootingEngine continues Decals Wheels and TiresKEY Part NO. NO. Description SCH12 SchematicElectrical KEY Part Description Chassis Chassis 196 DriveBolt Rdhd Sqnk 3/8-16 x 2-3/4 Gr Engine Spark Arrester KITEngine Power Rating Information Steering Assembly Seat Assembly Mower Deck KEY Part NO. NO. Description Mower Lift Limitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart Front Mounted Deck Riders Engine Transmission Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation10.27.10 JA