Husqvarna CTH151 XP owner manual Mulching Mowing Tips

Page 16

OPERATION

•Place tractor safely on level surface with engine off and parking brake set.

•Disengage transmission by placing freewheel control in freewheeling position (See “TOTRANSPORT” in this section of manual).

•Sitting in the tractor seat, start engine. After the engine is running, move throttle control to slow position. With motion control lever in neutral (N) position, slowly dis- engage clutch/brake pedal.

•Move motion control lever to full forward position and hold for fi ve (5) seconds. Move lever to full reverse position and hold for fi ve (5) seconds. Repeat this procedure three (3) times.

NOTE: During this procedure there will be no movement of drive wheels. The air is being removed from hydraulic drive system.

•Move motion control lever to neutral (N) position. Shut- off engine and set parking brake.

•Engage transmission by placing freewheel control in driving position (See “TO TRANSPORT” in this section of manual).

•Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. With motion control lever in neutral (N) position, slowly disengage clutch/brake pedal.

•Slowly move motion control lever forward, after the tractor moves approximately five (5) feet, slowly move motion control lever to reverse position. After the trac- tor moves approximately five (5) feet return the mo- tion control lever to the neutral (N) position. Repeat this procedure with the motion control lever three (3) times.

•Your transmission is now purged and now ready for normal operation.

MOWING TIPS

•Mower should be properly leveled for best mowing per- formance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

•The left hand side of mower should be used for trim- ming.

•Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the machine. This will result in a more even distribution of clippings and more uniform cutting.

•When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until fi nished (See Fig. 14).

00272

FIG. 14

•If grass is extremely tall, it should be mowed twice to reduce load and possible fi re hazard from dried clip- pings. Make first cut relatively high; the second to the desired height.

•Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

•Always operate engine at full throttle when mow- ing to assure better mowing performance and proper discharge of material. Regulate ground speed by se- lecting a low enough gear to give the mower cutting performance as well as the quality of cut desired.

•When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used.

MULCHING MOWING TIPS

IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER HOUSING FREE OF BUILT-UP GRASS AND TRASH. CLEAN AFTER EACH USE.

•The special mulching blade will recut the grass clip- pings many times and reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed. Also, the mulched grass will biode- grade quickly to provide nutrients for the lawn. Always mulch with your highest engine (blade) speed as this will provide the best recutting action of the blades.

•Avoid cutting your lawn when it is wet. Wet grass tends to form clumps and interferes with the mulching action. The best time to mow your lawn is the early afternoon. At this time the grass has dried the newly cut area will not be exposed to direct sunlight.

•For best results, adjust the mower cutting height so that the mower cuts off only the top one-third of the grass blades (See Fig.15).For extremely heavy mulch- ing, reduce your width of cut on each pass and mow slowly.

MAX 1/3

mulcher_9

FIG. 15

•Certain types of grass and grass conditions may require that an area be mulched a second time to completely hide the clippings. When doing a second cut, mow across (perpendicular) to the first cut path.

•Change your cutting pattern from week to week. Mow north to south one week then change to east to west the next week. This will help prevent matting and graining of the lawn.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents CTH151 XP Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationIII. Children ServiceIV. Towing Table of Contents Unassembled Parts Steering Wheel SeatAssembly Tools Required for AssemblyTo Remove Tractor from CAR- TON Before Removing Tractor from SkidInstall Seat See Fig To Install Bagger Components to Tractor See Figs A-4D To Assemble Bagger See FigsTo Assemble and Install Mulcher Plug See Fig Bagger Adjustment See FigHorizontal Adjustment Vertical AdjustmentCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Mulching Mowing TipsBagging See To Dump Bagger SeeTo Convert Mower See Maintenance Lubrication ChartGeneral Recommendations Before Each USETractor Blade CareEngine Cleaning To Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Check and Adjust Brake See Fig To Replace Mower Blade Drive Belt See FigTransmission REMOVAL/REPLACEMENT Transaxle Motion Control Lever Neutral ADJUSTMENTSee FigTo Adjust Steering Wheel Alignment To Replace Motion Drive Belt See FigTo Adjust Throttle Control Cable To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysStorage OtherFuel System Engine OILTroubleshooting Points With attachment clutch Service Notes Schematic TRACTOR- -MODEL NO. CTH151 XP HAUCT15H36F, Product no 17Electrical KEY Part Description Chassis and Enclosures 532 19 Drive Repair Parts Steering Assembly 532 19 Steering Wheel Seat Assembly 532 18 SeatDecals Wheels & TiresEngine Optional EquipmentMower Lift Mower Repair Parts Bagger Warranty Statement Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX

CTH151 XP specifications

The Husqvarna CTH151 XP is a state-of-the-art compact tractor designed for both commercial and residential use. This versatile machine is engineered to provide outstanding performance, efficiency, and user comfort, making it an ideal solution for a variety of landscaping tasks.

One of the standout features of the CTH151 XP is its powerful engine. Equipped with a robust engine that delivers ample horsepower, this tractor can effortlessly handle heavy workloads. Its efficient fuel consumption ensures that operators can work for extended periods without frequent refueling, leading to increased productivity and cost savings.

The CTH151 XP boasts an innovative transmission system, featuring a hydrostatic drive that allows for smooth and precise control at various speeds. This feature is especially valuable for tasks that require nuanced maneuvering, such as mowing or trimming in tight spaces. The dual pedals enable easy speed and direction changes, enhancing the overall driving experience.

Another notable characteristic of the CTH151 XP is its ergonomic design. The comfortable seating arrangement and user-friendly controls are designed to reduce operator fatigue, allowing for long hours of efficient operation. The adjustable steering wheel and controllable armrests provide additional comfort, enabling users to find their ideal driving position.

Husqvarna has integrated advanced technology into the CTH151 XP, ensuring that it meets modern landscaping demands. The built-in cutting deck features an adjustable height, allowing for precise lawn maintenance. This feature is particularly beneficial for achieving a professional finish on varying terrain.

The CTH151 XP is designed with durability in mind. Its rugged construction and high-quality materials ensure that the tractor can withstand harsh operating conditions. Furthermore, the tractor’s maintenance-friendly design allows for easy access to key components, making routine maintenance tasks more straightforward.

The compact size of the CTH151 XP makes it maneuverable in confined spaces while still providing a powerful performance comparable to larger tractors. Lawn care professionals and homeowners alike will appreciate its versatility, as it can easily transition from mowing to snow clearing or hauling.

In summary, the Husqvarna CTH151 XP combines power, versatility, and comfort in a package that meets the demands of any landscaping task. With its advanced technology, ergonomic design, and durable construction, this compact tractor is a reliable choice for those seeking efficiency and effectiveness in their outdoor projects.
Top Page Image Contents