Husqvarna CTH151 XP To Replace Motion Drive Belt See Fig, Transmission REMOVAL/REPLACEMENT

Page 25

SERVICE AND ADJUSTMENTS

TO REPLACE MOTION DRIVE BELT (See Fig. 31)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

Disconnect clutch wire harness.

Remove clutch locator.

Remove belt from clutching idler and all stationary idlers.

Remove belt downward from engine pulley and around electric clutch.

Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades.

BELT INSTALLATION -

Carefully work new belt down around transmission cooling fan and onto the input pulley.

Pull belt toward front of tractor and roll belt around electric clutch and onto engine pulley.

Install belt through all stationary idlers and clutching idler.

Reinstall clutch locator and tighten nut securely.

Reconnect clutch harness.

Make sure belt is in all pulley grooves and inside all belt guides and keepers.

Install mower (See “TO INSTALL MOWER” in this sec- tion of manual).

CLUTCH LOCATOR

ELECTRIC

CLUTCH

 

CLUTCHING

IDLER

STATIONARY

IDLERS

CLUTCH

WIRE HARNESS

TRANSMISSION

INPUT PULLEY

02201

FIG. 31

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See“PURGETRANSMISSION” in the Operation section of this manual.

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT(See Fig. 32)

The motion control lever has been preset at the factory and adjustment should not be necessary.

Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

Start engine and move motion control lever until tractor does not move forward or backward.

Hold motion control lever in that position and turn engine off.

While holding motion control lever in place, loosen the adjustment bolt.

Move motion control lever to the neutral (N) (lock gate) position.

Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

Loosen the adjustment bolt.

Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

Tighten adjustment bolt securely.

Start engine and test.

If tractor still creeps, repeat above steps until satis- fied.

MOTION CONTROL

NEUTRAL

LEVER

LOCK GATE

 

ADJUSTMENT

BOLT

FIG. 32

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

25

Image 25
Contents CTH151 XP Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationIII. Children ServiceIV. Towing Table of Contents Steering Wheel Seat Unassembled PartsTools Required for Assembly AssemblyTo Remove Tractor from CAR- TON Before Removing Tractor from SkidInstall Seat See Fig To Assemble Bagger See Figs To Install Bagger Components to Tractor See Figs A-4DBagger Adjustment See Fig To Assemble and Install Mulcher Plug See FigHorizontal Adjustment Vertical AdjustmentCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigMulching Mowing Tips Mowing TipsBagging See To Dump Bagger SeeTo Convert Mower See Lubrication Chart MaintenanceGeneral Recommendations Before Each USEBlade Care TractorEngine Cleaning To Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig To Check and Adjust Brake See FigTransaxle Motion Control Lever Neutral ADJUSTMENTSee Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment To Replace Motion Drive Belt See FigTo Adjust Carburetor To Adjust Throttle Control CableTo Replace Headlight Bulb Interlocks and RelaysOther StorageFuel System Engine OILTroubleshooting Points With attachment clutch Service Notes TRACTOR- -MODEL NO. CTH151 XP HAUCT15H36F, Product no 17 SchematicElectrical KEY Part Description Chassis and Enclosures 532 19 Drive Repair Parts Steering Assembly 532 19 Steering Wheel 532 18 Seat Seat AssemblyWheels & Tires DecalsOptional Equipment EngineMower Lift Mower Repair Parts Bagger Warranty Statement Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

CTH151 XP specifications

The Husqvarna CTH151 XP is a state-of-the-art compact tractor designed for both commercial and residential use. This versatile machine is engineered to provide outstanding performance, efficiency, and user comfort, making it an ideal solution for a variety of landscaping tasks.

One of the standout features of the CTH151 XP is its powerful engine. Equipped with a robust engine that delivers ample horsepower, this tractor can effortlessly handle heavy workloads. Its efficient fuel consumption ensures that operators can work for extended periods without frequent refueling, leading to increased productivity and cost savings.

The CTH151 XP boasts an innovative transmission system, featuring a hydrostatic drive that allows for smooth and precise control at various speeds. This feature is especially valuable for tasks that require nuanced maneuvering, such as mowing or trimming in tight spaces. The dual pedals enable easy speed and direction changes, enhancing the overall driving experience.

Another notable characteristic of the CTH151 XP is its ergonomic design. The comfortable seating arrangement and user-friendly controls are designed to reduce operator fatigue, allowing for long hours of efficient operation. The adjustable steering wheel and controllable armrests provide additional comfort, enabling users to find their ideal driving position.

Husqvarna has integrated advanced technology into the CTH151 XP, ensuring that it meets modern landscaping demands. The built-in cutting deck features an adjustable height, allowing for precise lawn maintenance. This feature is particularly beneficial for achieving a professional finish on varying terrain.

The CTH151 XP is designed with durability in mind. Its rugged construction and high-quality materials ensure that the tractor can withstand harsh operating conditions. Furthermore, the tractor’s maintenance-friendly design allows for easy access to key components, making routine maintenance tasks more straightforward.

The compact size of the CTH151 XP makes it maneuverable in confined spaces while still providing a powerful performance comparable to larger tractors. Lawn care professionals and homeowners alike will appreciate its versatility, as it can easily transition from mowing to snow clearing or hauling.

In summary, the Husqvarna CTH151 XP combines power, versatility, and comfort in a package that meets the demands of any landscaping task. With its advanced technology, ergonomic design, and durable construction, this compact tractor is a reliable choice for those seeking efficiency and effectiveness in their outdoor projects.