Asus TX97-X manuals
Computer Equipment > Computer Hardware
When we buy new device such as Asus TX97-X we often through away most of the documentation but the warranty.
Very often issues with Asus TX97-X begin only after the warranty period ends and you may want to find how to repair it or just do some service work.
Even oftener it is hard to remember what does each function in Computer Hardware Asus TX97-X is responsible for and what options to choose for expected result.
Fortunately you can find all manuals for Computer Hardware on our side using links below.
64 pages 853.48 Kb
2 USER'S NOTICE•Intel, LanDesk, and Pentium are registered trademarks of Intel Corporation •Symbios is a registered trademark of Symbios Logic Corporation •Windows and MS-DOSare registered trademarks of Microsoft Corporation •Sound Blaster AWE32 and SB16 are trademarks of Creative Technology Ltd •Adobe and Acrobat are registered trademarks of Adobe Systems Incorporated © Copyright 1997 ASUSTeK COMPUTER INC. All rights reserved Product Name: ASUS TX97-X Manual Revision: Release Date: March ASUS TX97-XUser's Manual 3 ASUSTeK COMPUTER INCMarketing Info: Technical Support: ASUS COMPUTER INTERNATIONAL ASUS COMPUTER GmbH 4 CONTENTS6 FCC & DOC COMPLIANCEFederal Communications Commission Statement •This device may not cause harmful interference, and •Re-orientor relocate the receiving antenna •Increase the separation between the equipment and receiver •Consult the dealer or an experienced radio/TV technician for help Canadian Department of Communications Statement 7 How this manual is organizedItem Checklist 8 Features of the ASUS TX97-XMotherboard10 II.FEATURES12 Map of the ASUS Motherboard14 Installation Steps1. Jumpers 16 III.INSTALLATION21 2.System Memory (DIMM)23 3.Central Processing Unit (CPU)24 4.Expansion Cards26 5.External Connectors34 Support SoftwareFlash Memory Writer Utility 37 6. BIOS SetupLoad Defaults 38 Standard CMOS Setup39 Details of Standard CMOS Setup:40 For IDE hard disk drive setup, you can:•Use the Auto setting for detection during bootup •Enter the specifications yourself manually by using the “User” option CYLS HEAD PRECOMP LANDZ SECTOR MODE SIZE Auto detection of hard disks on bootup Auto NOTE: SETUP Defaults are noted in parenthesis next to each function heading 41 Drive A / Drive B (None)Floppy 3 Mode Support (Disabled) Drive A, Drive B, Both, and Disabled Video (EGA/VGA) EGA/VGA, Mono (for Hercules or MDA), CGA 40, and CGA Halt On (All Errors) 42 BIOS Features SetupDetails of BIOS Features Setup 43 Quick Power On Self Test (Enabled)Enabled HDD Sequence SCSI/IDE First (IDE) IDE SCSI Boot Sequence (C,A) A,CDROM,C CDROM,C,A D,A E,A; F,A; C only, A,C C, A Boot Up Floppy Seek (Disabled) When enabled, the BIOS will seek the floppy "A" drive one time Floppy Disk Access Control (R/W) IDE HDD Block Mode Sectors (HDD MAX) Security Option (System) PS/2 Mouse Function Control (Auto) Disabled 44 PCI/VGA Palette Snoop (Disabled)OS/2 Onboard Memory > 64M (Disabled) Video ROM BIOS Shadow (Enabled) C8000-CBFFFto DC000-DFFFF(Disabled) Boot Up NumLock Status (On) Off Boot Up System Speed (High) This has no function and should be left on the setup default Typematic Rate Setting (Disabled) Disabled Typematic Rate (Chars/Sec) 8, 10, 12, 15, 20, 24 Typematic Delay (Msec) (250) 45 Chipset Features SetupDetails of Chipset Features Setup 46 (ChipsetDelayed Transaction (Disabled) 16-bitI/O Recovery Time (1 BUSCLK) Timing for 16-bitISA cards 8-bitI/O Recovery Time (1 BUSCLK) Timing for 8-bitISA cards Video BIOS Cacheable (Enabled) Memory Hole at Address (None) 14MB-16MB 15MB-16MB Onboard FDC Controller (Enabled) Onboard FDC Swap A & B (No Swap) Onboard Serial Port 1 (3F8H/IRQ4) Settings are and for the onboard serial connector Onboard Serial Port 2 (2F8H/IRQ3) Settings are 3F8H/IRQ4, 2F8H/IRQ3, 3E8H/IRQ4, 2E8H/IRQ10, and Disabled for for the onboard serial connector 47 Onboard Parallel Port (378H/IRQ7)3BCH / IRQ 7, 378H / IRQ 7, 278H / IRQ 5, Disabled Parallel Port Mode (ECP+EPP) ECP DMA Select (3) ECP ECP+EPP Parallel Port Mode UART2 Use Infrared (Disabled) infrared module connector Onboard PCI IDE Enable (Both) Primary Secondary Both Disable IDE Ultra DMA Mode (Auto) 0, 1, 2, 3 48 Power Management SetupDetails of Power Management Setup 49 Video Off Method (V/H SYNC + Blank)PWR Button < 4 Secs (Soft Off) Soft Off Suspend No Function PWR Up On Modem Act (Enabled) AC PWR Loss Restart (Disabled) PM Timers (Disabled) HDD Power Down Mins Disable 50 PNP and PCI SetupDetails of PNP and PCI Setup 51 Slot 1/2/3/4 IRQ (Auto)Auto NA, 9, 10, 11, 12, 14, or PCI Latency Timer (32 PCI Clock) "32 PCI Clock" enables maximum PCI performance for this motherboard IRQ xx Used By ISA (No/ICU) DMA x Used By ISA (No/ICU) ISA MEM Block BASE (No/ICU) SCSI BIOS (Auto) and PCI) 52 Load BIOS DefaultsLoad Setup Defaults 53 Supervisor Password and User Password54 IDE HDD Auto Detection55 Save and Exit SetupExit Without Saving 56 ASUS TX97 Motherboard Series Support CDLANDesk Client Manager (LDCM) 57 V.SUPPORT SOFTWARE•Custom Setup: (For Experienced Users) Choose File | New from the 2.Make the appropriate settings on the right-handside. Note following: -I2C and Network should not be modified 3.Choose LM78 from the pull-downmenu. Note the following: The fans are -Change the Threshold RPM to 1,500 RPM -Change the Threshold RPM Min to 1,320 RPM 4.Click Save button to save settings and exit 5.Choose File|Save from pull-downmenu, enter a file name, click Save 6.Exit the program screen NOTES: 4.CPU B Fan must be at least 2,660 RPM to be monitored by the LDCM 5.Fan labels are not consistent, use this table for reference: PC Health LDCM Notification Config Chassis CPU CPU A CPU B Extra Power 7.The administrator LDCM cannot cross a network bridge to other workgroups 8.AMD and Cyrix CPUs cannot be detected by the LDCM 9.The COM port that is in use will not show up in "Input/Output Ports SOFTWARE (LDCM) 58 Desktop Management Interface (DMI)61 SCSI BIOS and Drivers62 The ASUS PCI-SC200SCSI Interface Card
Also you can find more Asus manuals or manuals for other Computer Equipment.