Renesas M3062PT-EPB manuals

80 pages1.03 Mb

3To use the product properly
- Precautions for Safety:
Preface
4Contents
6Terminology
7Chapter 1. Precautions for Safety
8 WARNING IMPORTANT
CAUTION
- 12Note on NMI* Input:
- Note on RDY* Input:
- Note on HOLD* Input:
- Note on Clock Supply to the MCU:
- Notes on Maskable Interrupts:
- 13Notes on Reset Vector Area:
- Note on Accessing Address 00000h:
- Note on Access Prohibited Area:
- Notes on Stack Area:
- Note on Stop and Wait Modes:
- 14Note on Display of MCU Status:
- Note on Breaks:
- Notes on Address-Match Breaks:
- 15Notes on Address-Match Interrupts:
- Notes on Software Breaks:
- 16Note on Differences between the Actual MCU and Emulator:
- Note on the Watchdog Function:
- Note on DMA Transfer:
- 17Note on Protect Register:
- Notes on Internal Flash ROM of the MCU:
- Notes on Pullup Control:
- Note on Operating Frequency:
- 18Notes on Debugging in CPU Rewrite Mode:
- 19Chapter 2. Preparation
  - 202.1 Package Components
    - * For purchasing these products, contact your local distributor.
  - 2.2 Other Tool Products Required for Development
  - 212.3 Name of Each Part
  - 23Note on Usage in Memory Expansion or Microprocessor Mode:
  - Note on Accessing Address 00000h:
  - Note on the Target Status POWER LED:
  - Note on the Target Status CLOCK LED:
    - 242.4 When Using the Emulator for the First Time
- 25Chapter 3. Setup
  - 263.1 Selecting Clock Supply
    - (1) Kinds of Oscillator Boards
    - (2) Replacing an Oscillator Circuit Board
  - 27Note on Replacing the Oscillator Circuit Board:
    - 3.2 Switch Settings
  - 30Note on Using the Internal Generator Circuit:
    - 3.3 A-D Conversion Bypass Capacitors
  - 31Note on the A-D Converter Function:
    - 323.4 Pullup of Emulation Ports
    - 3.5 Connecting the PC7501
  - 33Note on Connecting the PC7501:
    - 3.6 Connecting the Target System
      - Figure 3.11 shows how to connect this product according to your target system.
      - Figure 3.11 Connecting the target system according to target systems
  - 34Note on Connecting the Target System:
    - 39*
    - 40*
    - 42*
    - 43*
- 45Chapter 4. Usage
  - 464.1 Turning On the Power
  - 47Note on Memory Expansion or Microprocessor Mode:
  - Note on the Target Status POWER LED:
    - TARGET
    - SYSTEM
  - Note on the Target Status CLOCK LED:
    - 4.2 Downloading Firmware
  - 48Note on Downloading Firmware:
    - 494.3 Self-check
      - Figure 4.3 LED displays in the self-check
- 51Chapter 5. Specifications
  - 525.1 Specifications
    - Table 5.1 Specifications of the M3062PT-EPB
  - 535.2 Operation Timing of Memory Expansion Mode and Microprocessor Mode (5 V)
    - (1) Separate Bus Timing
      - -40 [ns] n: "3" for 3-wait
      - -40 [ns] n: "2" for 2-wait
    - 55(2) Multiplex Bus Timing
      - *3 Calculated by the following formula according to the frequency of BCLK.
      - -25 [ns]
    - 57(3) Timing Requirements
      - Tables 5.4 and Figure 5.3 list the timing requirements. Table 5.4 Timing requirements
  - 585.3 Operation Timing of Memory Expansion Mode and Microprocessor Mode (3 V)
    - (1) Separate Bus Timing
      - -40 [ns] n: "3" for 3-wait
    - 60(2) Multiplex Bus Timing
      - *3 Calculated by the following formula according to the frequency of BCLK.
      - -40 [ns]
      - -50 [ns] n: "2" for 2-wait
    - 62(3) Timing Requirements
  - 635.4 Connection Diagram
    - 64Table 5.8 Electrical characteristics of 74HC4066
    - Table 5.9 Electrical characteristics of port emulation EPGA
  - 706.1 Flowchart to Remedy the Troubles
    - Figure 6.1 Flowchart to remedy the troubles
  - 716.2 When the Emulator Debugger Does Not Start Up Properly
    - (1) When the LEDs of the PC7501 Shows an Error
      - Table 6.1 Errors LEDs show and their checkpoints
        See the user's manual of the PC7501.
        See the CLK command of the emulator
        See "3.1 Selecting Clock Supply" (page 26).
    - 72(2) MCU Setting Dialog Box Does Not Appear at Debugger Startup (target connected)
      - Table 6.2 Checkpoints of errors at debugger startup (target connected)
        See the user's manuals of the PC7501 and emulator
        See MCU specifications.
    - 73(3) MCU Setting Dialog Box Does Not Appear at Debugger Startup (target not connected)
      - Table 6.3 Checkpoints of errors at debugger startup (target not connected)
      - Table 6.4 Checkpoints of errors at debugger startup (target connected)
    - (4) Errors Occur at Debugger Startup (target connected)
      - See the user's manuals of the PC7501 and emulator
      - See MCU specifications.
- 76Chapter 7. Maintenance and Guarantee
  - 7.1 Maintenance
  - 7.2 Guarantee
  - 7.3 Repair Provisions
  - 7.4 How to Request for Repair
  - 77Note on Transporting the Product: