3M MP7650, MP7750 DVD player, VCR

3M™ Multimedia Projector MP7650/7750

Connecting to a DVD Player

RGB IN

	AUDIO IN			S-VIDEO IN
R	L / (MONO) VIDEO IN			S-VIDEO IN
R	L / (MONO) VIDEO IN
B B B				C
	CR / RR	CB / PB	Y

A A A

ENGLISH

COMPONENT VIIDEO	RGB OUT	CONTROL
	USB

	A		B	AUDIO/VIDEO	C
cableCOMPONENT	OUTVIDEOCOMPONENTIN VIDEOCOMPONENT	cableAUDIO/VIDEO		AUDIO/VIDEO	IN VIDEO-S
cableCOMPONENT	OUTVIDEOCOMPONENTIN VIDEOCOMPONENT	cableAUDIO/VIDEO		OUTAUDIO/VIDEO	OUTVIDEO-S
				IN
If using a component			If using an audio/video
video connection			connection

S-VIDEO cable

If using a S-video connection

DVD player

Connecting to a VCR

K				1	RGB IN	2
K
	AUDIO IN			S-VIDEO IN
R	L / (MONO) VIDEO IN			S-VIDEO IN
R	L / (MONO) VIDEO IN
A A A				B
	CR / RR	CB / PB	Y
COMPONENT		VIIDEO		RGB	OUT	CONTROL
				USB

	A
cable AUDIO/VIDEO	AUDIO/VIDEO IN AUDIO/VIDEO
	OUT

VIDEO-S

OUT VIDEO-S

S-VIDEO cable

If using a S-video connection

VCR

Contents

Page Page Thank you for purchasing this projector WARNING • Please read the ” thoroughly to ensure correct safe place for future reference NOTE ●Ultra High Brightness ●Keystone Distortion Correction ●Partial Magnification Function ●Whisper Mode Equipped •Only use the power cord that came with the projector Connect your devices to the projector Connect your computer, VCR and/or other devices you will be using to the projector Insert the batteries into the remote control The Projector THE REMOTE CONTROL FRANÇAIST CAUTION Press and hold in the elevator 1 buttons Raise or lower the projector to the 2 desired height and then release the elevator buttons The screen Top view If 4:3 aspect ratio Side view If 16:9 aspect ratio Indicates the corresponding reference page NOTE About Plug-and-PlayCapability Laptop computer Desktop computer DVD player VCR Display monitor Page Make sure that the power cord is firmly and correctly connected to the projector and outlet Turn on the projector's power NOTE Turn the power on/off in right order 3 Press the STANDBY/ON button (control panel or remote control) Remove the lens cap Using the remote control If selecting RGB input Press the RGB button If selecting video input Press the VIDEO button 1 Press the STANDBY/ON button (control panel or remote control) Press the STANDBY/ON button again (control panel or remote control) Check that the POWER indicator stops blinking and lights to solid Press the VOLUME button 2 Press the buttons to adjust the volume 1 Press the MUTE button 1 Press the POSITION button Use the the position Press the AUTO button Automatic Adjustment for RGB Input Automatic Adjustment for Video Input Page Page Page Page MAIN Menu PICTURE1 Menu PICTURE2 Menu INPUT Menu SCREEN Menu OPTION Menu PS/2, ADB, Serial Mouse Control USB Mouse/Keyboard Control If the replace lamp indicator (see "Related Messages •Do not use the projector with the lamp cover removed become your lamps when you power up Turn off the projector, and unplug the for at least 45 minutes, and prepare a new lamp cooled adequately, slowly flip over the projector, so that the bottom is facing up Page Page Caring for the inside of the projector : Caring for the lens : Caring for the cabinet and remote control transmitter : WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED hr Page WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED (continued) Phenomena That May Easily Be Mistaken for Machine Defects 10 30 Item Specification Unit : mm Accessories Part Number RGB IN [1]/[2] S-VIDEO RGB OUT signal Terminal Specification TECHNICAL Page The following signals are used for the initial settings ADB Mouse Serial Mouse USB Mouse PS/2 Mouse 19200bps, 8N1 1 Protocol 2 Header 3 Command data Command data chart Action (byte_0 - 1) Requesting projector status (Get command) Changing the projector settings (Set command) Using the projector default settings (Reset Command) Increasing the projector setting value (Increment command) Decreasing the projector setting value (Decrement command)