Manuals / Brands / Computer Equipment / Projector / 3M / Computer Equipment / Projector

3M MP7650, MP7750 1 Press the STANDBY/ON button (control panel or remote control), Press the STANDBY/ON button again, (control panel or remote control), orange, [O] (OFF)

1 52

Download 52 pages, 1.9 Mb

3M™ Multimedia Projector MP7650/7750

TURNING OFF THE POWER

			STANDBY/ON
VIDEO	RGB	SEARCH
ASPECT		AUTO	BLANK
MAGNIFY	HOME	PAGE UP	VOLUME
ON
	END	PAGE DOWN	MUTE
OFF
FREEZE		KEYSTONE
POSITION			MENU
	ENTER
ESC			RESET

Control panel

LANP

TENP

POWER

STANDBY/ON INPUT KEYSTONE RESET

NOTE

•Except in emergencies, follow the above- mentioned procedure for turning power off.

1 Press the STANDBY/ON button (control panel or remote control)

The message "Power off?" will appear on the screen for approximately 5 seconds.

STANDBY/ON

2	Press the STANDBY/ON button again
	(control panel or remote control)

Press the STANDBY/ON button again while the "Power off?" message is visible. The projector lamp goes off and starts cooling down. The POWER indicator blinks orange while the lamp cools down. (Pressing the STANDBY/ON button while the POWER indicator is blinking orange has no effect.)

The system goes into the STANDBY mode after cooling down and the POWER indicator stops blinking orange and then lights to solid orange.

STANDBY/ON

3	Check that the POWER indicator stops
	blinking and lights to solid	power switch
	orange.
	Switch the power switch to
	[O] (OFF).

POWER indicator

			STANDBY/ON	INPUT			LANP
					KEYSTONE	RESET	TENP
			LANP			RESET	POWER
KEY			LANP
KEY			TENP
STONE	RESET	POWER	TENP
	RESET	POWER

4	Confirm that the POWER indicator has
	gone off and then attach the lens cap.

When the projector has completed powering down, the POWER indicator will go off.

16	© 3M 2002. All Rights Reserved.

Contents

Page Page Thank you for purchasing this projector WARNING • Please read the ” thoroughly to ensure correct safe place for future reference NOTE ●Ultra High Brightness ●Keystone Distortion Correction ●Partial Magnification Function ●Whisper Mode Equipped •Only use the power cord that came with the projector Connect your devices to the projector Connect your computer, VCR and/or other devices you will be using to the projector Insert the batteries into the remote control The Projector THE REMOTE CONTROL FRANÇAIST CAUTION Press and hold in the elevator 1 buttons Raise or lower the projector to the 2 desired height and then release the elevator buttons The screen Top view If 4:3 aspect ratio Side view If 16:9 aspect ratio Indicates the corresponding reference page NOTE About Plug-and-PlayCapability Laptop computer Desktop computer DVD player VCR Display monitor Page Make sure that the power cord is firmly and correctly connected to the projector and outlet Turn on the projector's power NOTE Turn the power on/off in right order 3 Press the STANDBY/ON button (control panel or remote control) Remove the lens cap Using the remote control If selecting RGB input Press the RGB button If selecting video input Press the VIDEO button 1 Press the STANDBY/ON button (control panel or remote control) Press the STANDBY/ON button again (control panel or remote control) Check that the POWER indicator stops blinking and lights to solid Press the VOLUME button 2 Press the buttons to adjust the volume 1 Press the MUTE button 1 Press the POSITION button Use the the position Press the AUTO button Automatic Adjustment for RGB Input Automatic Adjustment for Video Input Page Page Page Page MAIN Menu PICTURE1 Menu PICTURE2 Menu INPUT Menu SCREEN Menu OPTION Menu PS/2, ADB, Serial Mouse Control USB Mouse/Keyboard Control If the replace lamp indicator (see "Related Messages •Do not use the projector with the lamp cover removed become your lamps when you power up Turn off the projector, and unplug the for at least 45 minutes, and prepare a new lamp cooled adequately, slowly flip over the projector, so that the bottom is facing up Page Page Caring for the inside of the projector : Caring for the lens : Caring for the cabinet and remote control transmitter : WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED hr Page WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED (continued) Phenomena That May Easily Be Mistaken for Machine Defects 10 30 Item Specification Unit : mm Accessories Part Number RGB IN [1]/[2] S-VIDEO RGB OUT signal Terminal Specification TECHNICAL Page The following signals are used for the initial settings ADB Mouse Serial Mouse USB Mouse PS/2 Mouse 19200bps, 8N1 1 Protocol 2 Header 3 Command data Command data chart Action (byte_0 - 1) Requesting projector status (Get command) Changing the projector settings (Set command) Using the projector default settings (Reset Command) Increasing the projector setting value (Increment command) Decreasing the projector setting value (Decrement command)