Section 7: Troubleshooting
7.1 Sympton/Solution Table
|
|
| ENGLISH | |
Symptom | Cause | Solution | ||
| ||||
|
|
|
| |
Power cannot be turned | • The Main power is not turned on. | • Turn the MAIN POWER switch on. |
| |
on. | • The power cord is disconnected. | • Insert the power cord into an AC socket. |
| |
|
| |||
|
|
|
| |
No picture and sound | • The setting of the input source is not | • Set the correct input using the input select button |
| |
| correct. | of the projector or the remote control. |
| |
| •RGB/Video/Audio wiring to projector is | • Connect the cable to correct input/output source. |
| |
| not correct. |
|
| |
|
|
|
| |
Sound is heard with | • RGB/Video wiring to projector is not correct. | • Connect the cable to correct input/output source. |
| |
• Press the MENU button and increase |
| |||
no picture |
|
| ||
| • The brightness is set fully to dark. | BRIGHTNESS. |
| |
|
|
|
| |
Picture is displayed | • Audio wiring to projector is not correct. | • Connect the cable to correct input/output source. |
| |
• The volume is set to minimum. |
| |||
• Press the VOL button and increase VOLUME. |
| |||
with no sound |
| |||
| • The unit is muted. | • Press the MUTE button. |
| |
|
|
|
| |
Color is weak and tint is | • The color and tint have been adjusted | • Adjust the color and tint correctly. |
| |
incorrect | incorrectly. |
| ||
|
| |||
|
|
|
| |
Picture is dark | • The brightness and contrast has been | • Adjust the brightness and contrast correctly. |
| |
| adjusted incorrectly. |
| ||
|
|
| ||
| • The lamp needs to be replaced. | • Replace the lamp with a new one. |
| |
|
|
| ||
|
|
|
| |
Picture is not clear | • Projector is out of focus. | • Adjust the focus. |
| |
|
|
|
| |
LAMP indicator lights | • Lamp will not ignite. | • Turn off power and let cool for 20 minutes, then restart. |
| |
red. | • If problem persists call your dealer. |
| ||
|
| |||
|
|
|
| |
LAMP indicator blinks | • Air filter door on bottom of case is open. | • Ensure air filter door is closed. |
| |
red. |
|
|
| |
TEMP indicator lights | • Temperature inside projector is too hot. | • Do not block the ventilation holes. |
| |
red. |
| • Clean air filter |
| |
|
|
|
| |
TEMP indicator blinks | • Cooling fan may be obstructed by metal | • Align metal screen. |
| |
red. | screen under foam air filter. | • If fan blade is still obstructed, call service. |
| |
|
|
|
|
7.2 Message/Solution Table
| Error Message Displays | Cause | Solution |
|
|
|
|
|
|
| NO INPUT IS DETECTED | The projector is not detecting a signal. | Check cable connections to input device. Input device not |
|
|
|
| connected to this input mode, switch to next mode. |
|
|
|
|
|
|
| SYNC IS OUT OF RANGE | The horizontal frequency of input signal | Switch projector to correct resolution. |
|
|
| exceeds projector capability. | See Appendix A.5 |
|
|
|
|
|
|
| CHANGE THE LAMP | Lamp operation time is greater than 1,900 | Change the projector lamp and reset the lamp operation |
|
|
| hours. | hours to zero. |
|
|
|
|
|
|
| RESET THE LAMP TIMER | Lamp operating time is greater than 2000 | Change the projector lamp and reset the lamp operation |
|
|
| hours. Safety feature shuts projector down | hours to zero. |
|
|
| after 10 minutes. |
|
|
|
|
|
|
|
| CHECK THE AIR FLOW | Air flow to cooling fan is blocked. | Clear air flow path to fan and clean air filter. |
|
|
|
|
|
|
|
|
|
|
|
© 3M 1999 | 3M™ Multimedia Projector MP8740 | 17 | ||
