audio adjustments

Adjust the gain of the subwoofer amplifier to blend in with the midrange and high frequency speakers. Ideally the amplifier powering the ie subwoofer has an electronic crossover, If it does adjust it for the best sound quality, the crossover setting should be between 50-100 Hz. If the amplifier does not have an electronic crossover, a 5 mH coil in series with the enclosure is acceptable. If the system is lacking mid-bass response reverse the speaker wires to the ie subwoofer and listen again. If the mid-bass response improves leave it alone, if not return the wires to the original position.

1. First turn factory radio to 3/4 volume.

2. Turn up/down gain to blend with mid and high speakers.

3. Adjust crossover of amplifier for best sound.

4. Repeat steps 2 and 3 until desired sound is achieved.

5

unpacking

These subwoofers are heavy. Rather than lifting the unit out of the shipping carton, turn the open carton over, and lift it off the subwoofer. Then remove the packing corners from the subwoofer and then remove it from the plastic bag.

placement

Unlike high frequency sound, our ears have difficulty locating the source of deep bass sounds. Consequently, you have a fair amount of flexibility in where you place the subwoofer in your vehicle. Typically the subwoofer is mounted in rear of the vehicle, either in the trunk, hatchback, or rear cargo area. For proper performance the port must not be closer than 3" from any walls, this will cause the performance to suffer. The enclosure can stand up or lie it on its side.

mounting locations

Brackets are supplied for mounting the enclosure either vertically or horizontally. Remove the proper screws from the enclosure and replace the screws through the bracket and then into the enclosure. Repeat for the other side. Screw the enclosure into the floor of the vehicle being careful to note where brake and fuel lines run on the other side. Do not mount the enclosure directly against a hard surface with out first putting down a piece of felt or cloth to prevent buzzes and rattles. Check to make sure that the enclosure screws are tightened properly, failure to do so may cause unwanted air leaks. Check to make sure that the screws mounting the enclosure to the floor are secure and tight.

warnings and tips

Always disconnect the battery ground wire before doing any work on your vehicle. Reconnect the cable only after the installation is complete and the wiring has been checked to make sure that there are no problems. If your radio features a code type security system, be sure you know the code before disconnecting the battery!

2

Page 2 Page 4
Page 3
Image 3
a/d/s/ IE6.1 / IE6.2 owner manual Audio adjustments, Unpacking, Placement, Mounting locations
Page 2 Page 4

IE6.1 / IE6.2 specifications

A/D/S refers to a advanced networking protocol designed to improve communication and data exchange across various systems. Specifically, IE6.1 and IE6.2 are versions within the A/D/S framework that incorporate unique features and technologies aimed at enhancing both efficiency and reliability in data transfer.

IE6.1 is recognized for its foundational improvements in data encapsulation and transmission capabilities. It introduces a robust error-checking algorithm that ensures data integrity during transfers, significantly reducing the likelihood of corrupt data packets. The protocol employs a modular architecture, allowing for easy integration with existing network infrastructures, which is crucial for organizations looking to upgrade without overhauling their entire systems.

A key feature of IE6.1 is its support for multiple transmission types, including voice, video, and data streams. This versatility makes it suitable for a variety of applications, from telecommunication services to real-time streaming. The protocol also incorporates adaptive bandwidth management, dynamically allocating resources based on current network conditions to optimize performance.

In contrast, IE6.2 builds upon the groundwork established by its predecessor, introducing advanced features such as enhanced security protocols and improved scalability. With the rising importance of data protection, IE6.2 implements encryption techniques that safeguard data both in transit and at rest. This emphasis on security addresses growing concerns regarding data breaches and unauthorized access.

IE6.2 also offers improved interoperability with legacy systems, making it easier for organizations to transition to this new standard while maintaining compatibility with older technologies. This backward compatibility is crucial for businesses that cannot afford extensive downtime during system upgrades.

One of the standout characteristics of IE6.2 is its support for Internet of Things (IoT) devices. As the number of connected devices continues to grow rapidly, IE6.2 accommodates the need for efficient data communication among these devices, facilitating smart environments across various industries.

Overall, both IE6.1 and IE6.2 provide essential enhancements to the A/D/S framework, focusing on reliability, security, and versatility. Organizations adopting these protocols can expect improved performance, enhanced data integrity, and a secure environment for their digital communications. As technology continues to evolve, these protocols will play a significant role in shaping the future of networking.
Top Page Image Contents