Depth-of-entry mark

Marking the depth of entry is a way to check if the pipe has reached the bottom of the fitting socket in step F. Measure the fitting depth and mark this distance on the pipe O.D. You may want to add several inches to the distance and make a second mark as the primer and cement will most likely destroy your first one.

Apply primer to the surface of the pipe and fitting socket with a natural bristle brush. This process softens and prepares the PVC or CPVC for the solvent cementing step. Move quickly and without hesitation to the cementing procedure while the surfaces are still wet with primer.

E.Application of solvent cement

•Apply the solvent cement evenly and quickly around the outside of the pipe at a width a little greater than the depth of the fitting socket.

•Apply a light coat of cement evenly around the inside of the fitting socket. Avoid puddling.

•Apply a second coat of cement to the pipe end.

STEP E

NOTE: Cans of cement and primer should be closed at all times when not in use to prevent evaporation of chemicals and hardening of cement. They are also very flammable and should be kept away from heat or flame.

F. Joint assembly

Working quickly, insert the pipe into the fitting socket bottom and give the pipe or fitting a 1/4" turn to evenly distribute the cement. Do not continue to rotate the pipe after it has hit the bottom of the fitting socket. A good joint will have sufficient cement to make a bead all the way around the outside of the fitting hub. The fitting will have a tendency to slide back while the cement is still wet so hold the joint together for about 15 seconds.

STEP F

G. Cleanup and joint movement

Remove all excess cement from around the pipe and fitting with a dry cotton rag. This must be done while the cement is still soft.

The joint should not be disturbed immediately after the cementing procedure, and sufficient time should be allowed for proper curing of the joint. Exact drying time is difficult to predict because it depends on variables such as temperature, humidity and cement integrity. For more specific information, you should contact your solvent cement manufacturer.

STEP G

OPERATION

WARNING

DO NOT ATTEMPT TO OPERATE WATER HEATER WITH COLD WATER INLET VALVE CLOSED.

NEVER OPERATE THE HEATER WITHOUT FIRST BEING CERTAIN IT IS FILLED WITH WATER AND A TEMPERATURE AND PRESSURE RELIEF VALVE IS INSTALLED IN THE RELIEF VALVE OPENING OF THE HEATER.

TO OPERATE THE HEATER

1.Close the heater drain valve by turning handle clockwise .

2.Open a nearby hot water faucet to permit the air in the system to escape.

3.Fully open the cold water inlet pipe valve allowing the heater and piping to be filled.

4.Close the hot water faucet as water starts to flow.

5.The heater is ready to be operated.

CAUTION

THE "ON/OFF" SWITCH ON TOP OF THE UNIT SHOULD NOT BE TURNED TO THE "OFF" POSITION UNLESS THE UNIT IS BEING SERVICED.

16

Page 15 Page 17
Page 16
Image 16
A.O. Smith BTX-80 warranty Operation, To Operate the Heater, Step E, Step F, Step G
Page 15 Page 17

BTX-80 specifications

The A.O. Smith BTX-80 is a high-efficiency water heater designed to meet the needs of both residential and light commercial applications. Engineered with the latest technology, this unit promises reliability and superior performance, making it a standout choice for those seeking an efficient hot water solution.

One of the primary features of the BTX-80 is its energy efficiency. With a high Energy Factor (EF) rating, this water heater is designed to minimize energy consumption while delivering reliable hot water. This feature not only helps owners save on utility bills but also contributes to a more sustainable living environment.

The BTX-80 utilizes advanced condensing technology, allowing it to extract heat from exhaust gases that would typically be expelled. This process enhances its efficiency and reduces the amount of fuel needed to heat water, ensuring that users benefit from lower operating costs. The unit comes equipped with a built-in power vent system, which allows for flexible installation options and an easy, straightforward setup.

Another notable characteristic of the A.O. Smith BTX-80 is its robust build quality. Designed with durable materials, it features a glass-lined tank that helps prevent rust and corrosion, extending the lifespan of the unit. The BTX-80 is also equipped with advanced insulation, which ensures minimal heat loss and improved energy retention.

Safety features are paramount when it comes to water heating, and the BTX-80 does not disappoint. It includes a fully integrated safety system that protects against overheating and excessive pressure, ensuring peace of mind for homeowners and business operators alike.

Additionally, the BTX-80 has a user-friendly digital display and diagnostic control system, allowing users to easily monitor and adjust settings. It also features multiple installation configurations to adapt to various space requirements.

In summary, the A.O. Smith BTX-80 water heater combines high energy efficiency, advanced condensing technology, robust construction, and user-friendly features. Ideal for those seeking a reliable and sustainable hot water solution, this model is a testament to A.O. Smith's commitment to innovation and quality in the water heating industry.
Top Page Image Contents