Ackton UPS45 manual Replacing the Battery Pack, Specifications, LEDs and Audible Alarms, Service

Replacing the Battery Pack

This UPS has an easy to replace hot-swappable battery pack.

Note: Please read the cautions in the BayStack Safety Guide.

Replacement Batteries

See your dealer or call the number in this manual for information on replacement battery pack kits. The order number for the battery pack is RBC18.

Battery Pack Replacement Procedure

Battery pack replacement is a safe procedure, isolated from electrical hazards. You may leave the UPS and loads on for the following procedure.

Notes

·Once the battery pack is disconnected, the loads are not protected from power outages.

·Be careful removing the batteries - they are heavy.

·Small sparks at the battery connectors are normal during connection.

APC	1.	Reach into the finger pull and remove the front cover.
	2.	Use a flat-blade screwdriver to turn the two battery door
		screws ¼ turn counterclockwise; open the door.
	3.	Grasp the clear plastic tab and gently pull the battery pack
		out of the UPS until the battery connector is visible.

Warning! Do not force the battery pack out. This may damage internal wiring!

4.	Disconnect the battery connector by gripping both sides of
	the connector and firmly pulling them apart.
5.	Slide the battery pack out of the UPS.
6.	Slide the new battery pack three-fourths of the way into the
	UPS.
7.	Connect the battery connector attached to the unit	to the
	connector attached to the new battery pack.

8.Push the battery pack in as far as it will go. There are stops in the back to prevent it from going too far.

9.Close the battery door, turn the battery compartment screws ¼ turn clockwise, and replace the front cover.

10.Batteries must be recycled. Deliver the battery to an appropriate recycling facility or ship it to the supplier in the new battery’s packing material. See the new battery instructions for more information.

Specifications

Acceptable input voltage	0 - 320 VAC
Input voltage (on-line operation)	165 - 283 VAC
Output voltage	208 - 253 VAC
Input Over Current Protection	Resettable circuit breaker
Frequency limits (on-line operation)	47 - 63 Hz (auto-sensing)
Transfer time	4 ms typical, blackout response time
Maximum load	450 VA 280 W
On-battery output voltage	230 VAC
On-battery frequency	50 or 60 Hz, ±0.1 Hz; unless synchronized to
	utility during brownout
On-battery waveshape	Stepped sine-wave
Output Over Current Protection	Overcurrent and short-circuit protected, latching
	shutdown on overload
Battery type	Spill proof, maintenance free, sealed lead-acid
Typical battery life	3 to 6 years, depending on number of discharge
	cycles and ambient temperature
Typical recharge time	4 to 8 hours from total discharge
Operating temperature	0 to +40 ° C (+32 to +104 ° F)
Storage temperature	-15 to +45 ° C (+5 to +113 ° F)
Operating and storage relative humidity	5 to 95%, non-condensing
Operating elevation	0 to +3,000 m (0 to +10,000 ft)
Storage elevation	0 to +15,000 m (0 to +50,000 ft)
Audible noise at 1 m (3 ft)	<38 dBA
Size (H x W x D)	4.5 x 44.5 x 33 cm.
	(1.75 x 17.5 x 13.0 in.)
Weight - net (shipping)	9.77 (11.82) kg.
	21.5 (26) lbs
Safety and approvals	VDE licensed to EN50091 and EN60950
EMC certification	EN55022
Electromagnetic Immunity	IEC 801-2 Level IV, 801-3 Level III,
	801-4 Level IV

LEDs and Audible Alarms

Function			LED		Tone*
	On Battery	On-Line	Overload	Replace Battery
UPS is on	l	m	l	l	—
UPS is running on battery	m	l	—	—	4
UPS is performing self-test	m	X	l	l	—
Overload	—	—	m	—	1
Overload shutdown	—	—	m	—	1
Output short circuit	—	—	m	—	1
Transformer failure	—	—	m	—	1
Low Battery (while on battery)	m	—	—	—	1
Replace battery condition	—	—	—	m	2
Battery disconnected in self test	l	l	l	l	3
UPS internal alarms:
boost/trim failure	X	X	l	l	1
transfer relay weld	X	X	X	X	1
Sleep Mode	—	X	X	—	—

Key:

— = irrelevant to condition	*	1	= sustained tone
m = on steady		2	= 1 minute of beeping every 5 hours
X = flashing		3	= fading tone
l = Off		4	= 4 beeps every 30 seconds

For further troubleshooting information, refer to “Troubleshooting” in the BayStack

Quick Reference Guide.

Service

How to Get Help

For product assistance, support contracts, or information about educational services, go to the following URL: http://www.baynetworks.com/corporate/contacts/ or telephone the Bay Networks Technical Solutions Center at:+011-978-916-3700.When asked for the Emergency Response Code, dial 177, and then the pound (#) sign.

Information about customer service is also available on the World Wide Web at: support.baynetworks.com.

Run Time

	150
	140
	130
	120	115
	110
Run	100
	90
Time
	80										25 `C
(min)
	70
	60
	50		51
	40			32.5
	30
					23
	20					19.5	15
								13	10	8.5
	10										6
	0
	0	40	80	120		160		200		240	280
				Output Load (watts)

Typical On-Battery Run Time vs. Load at 25° C

Declaration of Conformity

Application of Council Directives:		89/336/EEC,73/23/EEC,92/31/EEC,
		93/68/EEC,91/157/EEC
Standards to Which Conformity Declared:		EN55022, EN50082-1, EN50091, EN60950
Manufacturer's Name and Address:		American Power Conversion
		132 Fairgrounds Road
		West Kingston, Rhode Island, 02892, USA
		-or-
		American Power Conversion (A. P. C.) b. v.
		Ballybritt Business Park
		Galway, Ireland
		-or-
		American Power Conversion Phillipines
		Second Street
		Cavite EPZA
		Roserio, Cavite Phillipines
Importer's Name and Address:		American Power Conversion (A. P. C.) b. v.
		Ballybritt Business Park
		Galway, Ireland
Type of Equipment:		Uninterruptible Power Supply
Model Numbers:		PowerStack Models250 and 450, BayStack
		Model UPS45
Serial Numbers:		X9801 000 0000 —	X9899 999 9999*
		X9901 000 0000 —	X9999 999 9999*
Years of Manufacture:		1998, 1999
Note:		Where X = B, O, W, or D
We, the undersigned, hereby declare that the equipment			above directives.
Billerica, MA	10/1/98
Place	Date	Stephen A. Lee
		Regulatory Compliance Engineer
Galway, Ireland	10/1/98
Place	Date	Ray S. Ballard
		Managing Director, Europe

990-7062 Revision 1, 10/98