ADC AD-200 - page 56

G. BLOWER (SQUIRREL CAGE FAN) MOTOR ASSEMBLY

1. Blower (Squirrel Cage Fan) Motor Description

The dryer uses a 15-inch (38.1 cm) diameter, blower (squirrel cage fan) wheel. It spins (turns) in a

counterclockwise (CCW) direction when looking at the back of the blower housing.

The blower (squirrel cage fan) shaft is mounted in two (2) 1-3/8” (3.5 cm) diameter pillow block bearings,

and the shaft is driven by two (2) B-section V-belts connected to the blower (squirrel cage fan) motor.

The blower (squirrel cage fan) motor is mounted on an adjustable base. The blower (squirrel cage fan)

motor position can be easily adjusted so that the proper tension can be maintained on the V-belts.

Contents

Main Retain This Manual In A Safe Place For Future Reference Important Page Page Table of Contents Page Page Page SECTION I SAFETY PRECAUTIONS Page SECTION II ROUTINE MAINTENANCE A. CLEANING SUGGESTED CLEANING SCHEDULE Page B. LUBRICATION C. ADJUSTMENTS 11 SECTION III SPECIFICATIONS AND DIMENSIONS Gas*Steam* A. SPECIFICATIONS (GAS AND STEAM MODELS) Page SECTION IV INSTALLATION REQUIREMENTS A. ENCLOSURE/AIR SUPPLY/EXHAUST REQUIREMENTS B. ELECTRICAL AND GAS REQUIREMENTS NOTE: Any burner changes must be made by a qualified technician. C. OPERATIONAL SERVICE CHECK PROCEDURE SECTION V COMPONENT DESCRIPTION/REPLACEMENT Page NOTE: THE DSI GAS VALVES ARE NOT FIELD REPAIRABLE. 18 h. Troubleshooting Flowchart - Quick Reference... No Spark And System Does Not Work First Visual Check 19 i. Troubleshooting Flowchart - Quick Reference... Second Visual Check 20 j. Troubleshooting Flowchart - Quick Reference... Third Visual Check B. TROUBLESHOOTING THE DIRECT SPARK IGNITION (DSI) SYSTEM Page NOTE: Preliminary steps - DO NOT omit - to minimize the time required to troubleshoot this system. Page 25 d. Troubleshooting Flowchart - Quick Reference... First Visual Check I (Does Ignitor Spark?) . 26 Second Visual Check (Does Main Burner Ignite?) . 27 f. Troubleshooting Flowchart - Quick Reference... Third Visual Check (Does Main Burner Ignite?) Page NOTE: During the purge period, check to be sure that ALL shutoff valves are open. IMPORTANT: THE GAP SETTING ON THE IGNITOR/FLAME-PROBE ASSEMBLY IS CRITICAL. Page NOTE: To reset the DSI module if it is in the LOCKOUT mode, Ignitor Control Fault will display. Page Page NOTE: During the purge period, check to be sure that ALL shutoff valves are open. IMPORTANT: THE GAP SETTING ON THE IGNITOR/FLAME-PROBE ASSEMBLY IS CRITICAL. Page NOTE: To reset the DSI module if it is in the LOCKOUT mode, Ignitor Control Fault will display. Page C. NATURAL GAS AND LIQUID PROPANE (L.P.) GAS CONVERSION INSTRUCTIONS D. STEAM COIL SYSTEM OPERATION IMPORTANT:Coil failure due to improper PH level will VOID THE WARRANTY. Page Page Page E. SPRINKLER SYSTEM DESCRIPTION Page NOTE: Identify the wires removed for proper reinstallation. Page Page Page F. AIR JET ASSEMBLY Page Page Page Page NOTE: Make certain that the blower (squirrel cage fan) can spin freely. IMPORTANT: DO NOT OVERTIGHTEN V-BELTS. IMPORTANT: DO NOT OVERTIGHTEN V-BELTS. Page Page H. FILTER/REGULATOR ASSEMBLY NOTE: THIS SELF-RELIEVING FEATURE IS NOT DESIGNED TO BLEED THE DOWNSTREAM PRESSURE. I. DOOR SYSTEMS AUTOMATIC DOORS Page Page Page Page Page Page Page Page Page Page Page Page Page Page K. BASKET (TUMBLER) SYSTEM Page Page NOTE: Replace V-belts in matched sets (both belts). IMPORTANT: DO NOT OVERTIGHTEN TURNBUCKLE. IMPORTANT: Both drive wheels should be replaced as a set on the drive shaft assembly. Page Page Page Page Page SECTION VI Page SECTION VII PHASE 7 OPL SYSTEM DIAGNOSTICS A. DIAGNOSTIC (L.E.D. DISPLAY) FAULT MESSAGES Page Page Page Page Page Page SECTION VIII TROUBLESHOOTING Page Page Page Page P. Microprocessor controller (computer) reads Exhaust High Temp Fault... Q. Dryer operates but is taking too long to dry... R. Excessive noise and vibration...