ADTRAN 1204006L2 Bonding txadd-timer seconds, Bonding txcid-timer seconds, Description text

®

Quick Start Guide

For more detailed documentation, visit us online at www.adtran.com.

NetVanta ISDN BRI Dial Backup Interface Module (DIM) P/N 1200865L1

ISDN BRI DIM COMMANDS

alias <“text”>

Populates the ifAlias OID (Interface Table MIB of RFC2863) for all physical and virtual interfaces when using SNMP management station.

bonding txadd-timer <seconds>

Specifies the value (in seconds) for the aggregate call connect timeout. Use the no form of this command to return to the default value.

<seconds>	Specifies the number of seconds the endpoint will wait for
	additional channels (to add to the bonded aggregate) before
	considering the bonding negotiation a failure

bonding txcid-timer <seconds>

Specifies the value (in seconds) for the bearer channel (B-channel) negotiation timeout. Use the no form of this command to return to the default value.

<seconds>	Specifies the number of seconds the endpoint allots for
	negotiating data rates and channel capacities before
	considering the bonding negotiation a failure.

bonding txdeq-timer <seconds>

Specifies the value (in seconds) for the network delay equalization timeout. Use the no form of this command to return to the default value.

<seconds>	Specifies the number of seconds the endpoint allots for
	attempting to equalize the network delay between bearer
	channels before considering the bonding negotiation a failure.

bonding txfa-timer <seconds>

Specifies the value (in seconds) for the frame pattern detection timeout. Use the no form of this command to return to the default value.

<seconds>	Specifies the number of seconds the endpoint allots for
	attempting to detect the bonding frame pattern (when a call is
	connected) before considering the bonding negotiation a
	failure.

bonding txinit-timer <seconds>

Specifies the value (in seconds) for the originating endpoint negotiation timeout. Use the no form of this command to return to the default value.

<seconds>	Specifies the number of seconds the endpoint waits to detect
	the bonding negotiation frame pattern from the remote
	endpoint (when a call is connected) before considering the
	bonding negotiation a failure.

bonding txnull-timer <seconds>

Specifies the value (in seconds) for the answering endpoint negotiation timeout. Use the no form of this command to return to the default value.

<seconds>	Specifies the number of seconds the endpoint waits to detect
	the bonding negotiation frame pattern from the originating
	endpoint (after answering a call) before considering the
	bonding negotiation a failure.

caller-id override [always <number> if-no-CID <number>]

Configures the unit to replace caller ID information with a user-specified number. Use the no form of this command to disable any caller ID overrides.

always <number> Always forces replacement of the incoming caller ID number with the number given.

if-no-CID<number> Replaces the incoming caller ID number with the number given only if there is no caller ID information available for the incoming call.

description <text>

Identifies the specified interface, both physical and virtual (for example, circuit ID, contact information, etc.), using up to 80 alphanumeric characters.

isdn spid1 <spid> <ldn>

Specifies the Service Profile Identifiers (SPIDs). This information should be supplied by your service provider. Use the no form of this command to remove a configured SPID.

<spid>	Specifies the 8 to 14 digit number identifying your Basic Rate
	ISDN (BRI) line in the central office switch. A SPID is generally
	created using the area code and phone number associated
	with the line and a four-digit suffix.
<ldn>	Optional. Specifies the LDN assigned to the circuit by the
	service provider. The LDN is the number used by remote
	callers to dial into the ISDN circuit. If the <ldn> field is left
	blank, the AOS will not accept inbound dial-backup calls to the
	BRI module.

isdn spid2 <spid> <ldn>

See isdn spid1.

isdn switch-type [basic-5ess basic-dms basic-net3 basic-ni*]

Specifies the ISDN signaling type configured on the Basic Rate ISDN (BRI) interface. The type of ISDN signaling implemented on the BRI interface does not always match the manufacturer of the Central Office switch. Use the no form of this command to return to the default value. This setting is determined by your service provider.

basic-5ess	Specifies Lucent/AT&T 5ESS signaling.
basic-dms	Specifies Nortel DMS-100 custom signaling.The basic-dms
	signaling type is not compatible with proprietary SL-1 DMS
	signaling.
basic-net3	Specifies Net3 Euro-ISDN signalling.
basic-ni*	Specifies National-ISDN 1 signaling.
shutdown

Disables the interface (both physical and virtual) so that no data will be passed through. Use the no version of this command to turn on the interface and allows it to pass data.

*Indicates default values.

Quick Start Guide, 61200865L1-13E, July 2006 Technical Support 1-888-4ADTRAN (1-888-423-8726) Copyright © 2006 ADTRAN, All Rights Reserved