ADTRAN OPTI-T200 manual Provisioning Options, Account Provisioning, Software Upgrade, Compliance

TOTAL ACCESS OPTI - T200

PRICING AND AVAILABILITY 800.827.0807 TECHNICAL SUPPORT 800.726.8663 RETURN FOR REPAIR 256.963.8722 www.adtran.com 61184400L1-22A

PROVISIONING OPTIONS

Upon initial installation, the OPTI-T200 uses factory default settings. To provision the OPTI-T200, connect a terminal emulator via the RS-232 (DB-9) connector on the front panel. The terminal must be VT100 compatible and set for 9600 bps, 8 data bits, no parity and 1 stop bit. The following table lists the provisioning settings and their default values. The settings are retained in a nonvolatile memory device in case of power loss to the OPTI-T200.

Options	Settings (Default in Bold)
Service State	In Service, Out Of Service-Unassigned, Out Of Service-Maintenance
DS3 Provisioning
DS3 Interface	Enable, Disable
DS3 Line Build Out	Short, Long
Signal Fail (SF) Thresh	1x10-3, 1x10-4, 1x10-5
Signal Degrade (SD) Thresh	1x10-5, 1x10-6, 1x10-7, 1x10-8, 1x10-9
Clock Source (TX)	1.	Receive OC-3
	2.	Free Run
CLLI Code	User definable up to 20 characters
Network Provisioning
IP Address	User Defined
	Format = x.x.x.x where x = 0–255
Subnet Mask	User Defined
	Format = x.x.x.x where x = 0–255
Default Gateway	User Defined
	Format = x.x.x.x where x = 0–255
Telnet Menu Port	User defined = 0–65535 (23)
Telnet (TL-1) Port	User defined = 0–65535 (2001)
Time and Date	User Defined
Mount Location	Central Office, Remote
Account Provisioning	See the Account Provisioning section to the right of this table.
Restore Factory Defaults
Software Upgrade	TFTP, XModem, YModem

NOTE: To navigate through the menus, select the desired entry and press Enter. To work backward in the menus, press the Escape key. Some entries can be changed in only the Out-of-Service – Maintenance mode.

ACCOUNT PROVISIONING

1.Account 1

a)User Name – User Defined, up to 15 characters

b)Password – User Defined, up to 15 characters

c)Permission Level – Disabled, Read Only, Read-Write, Administrator

d)Delete Account

2.Account 2 – Same options as Account 1

3.Account 3 – Same options as Account 1

4.Account 4 – Same options as Account 1

5.Account 5 – Same options as Account 1

6.Account 6 – Same options as Account 1

7.Account 7 – Same options as Account 1

8.Account 8 – Same options as Account 1

9.Account 9 – Same options as Account 1

10.Account 10 – Same options as Account 1

SOFTWARE UPGRADE

Software download for the local OPTI-T200 is provided using XModem or YModem via the craft port or TFTP, XModem or YModem via Ethernet. Software download to a remote OPTI-T200 is accomplished either from the CO OPTI-T200 craft port or its Ethernet port. The download is carried over the DCC channel. TFTP is supported from only the Ethernet interface, and both systems would require IP addresses.

COMPLIANCE

This product intended for use in Restricted Access Areas only, and is intended to be installed in a Type “B” or “E” enclosure. This product complies with UL 60950.

Code	Input	Output
Power Code (PC)	F	C
Telecommunication Code (TC)	–	–
Installation Code (IC)	A	–

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by ADTRAN could void the user’s authority to operate this equipment.

WARRANTY

ADTRAN will replace or repair this product within the warranty period if it does not meet its published specifications or fails while in service. Warranty information can be found at www.adtran.com/warranty. U.S. and Canada customer Faxback: 877-457-5007, Document 414.