ADTRAN T1/FT1 + DSX-1 quick start DSX-1 RJ-48C C Onnection P Inouts

For more detailed documentation, visit us online at www.adtran.com.

®

NetVanta T1/FT1 + DSX-1 Network Interface Module (NIM) P/N 1202863L1

Quick Start Guide

INSTALLATION INSTRUCTIONS

	WAN-T1 DSX-1	DBU	1.	Remove the power from the unit.
			2.	Slide the option module into the option slot until the module is
				firmly seated against the chassis.
			3.	Secure the pins at both edges of the module.
			4.	Connect the cables to the associated device(s).
SPECIFICATIONS			5.	Complete installation of the base unit.
			6.	Restore power to the unit.

Operating	Frame Relay, Multilink Frame Relay,
Modes	PPP, Multilink PPP, HDLC		NetVanta modules should be installed only in
T1/FT1	Supported Standards: AT&T TR 62411, AT&T TR 54016,
Interface	Bellcore TR.194, ANSI T1.403		NetVanta Series products.
	Line Rate: 1.544 Mbps ±75 bps
	Line Code: AMI or B8ZS
		WAN-T1 NETWORK (RJ-48C) CONNECTION PINOUTS
	Framing: D4 (SF) or ESF
	FT1 Line Rate: DS0 channelized (multiples of 56/64 kbps)	Pin	Name	Description
	Input Signal: 0 to -36 dB (DS1)
		1	R1	Receive data from the network - Ring 1
	Line Build-Out: 0, -7.5, -15, -22.5 dB (long), 0 to 655 ft
		2	T1	Receive data from the network - Tip 1
	(short)
		3	—	Unused
	Connector: RJ-48C
	DS0 Assignment: Programmable	4	R	Transmit data toward the network - Ring
DSX-1	Supported Standards: ANSI T1.102	5	T	Transmit data toward the network - Tip
Interface	Line Rate: 1.544 Mbps	6-8	—	Unused
	DSX Receiver Input Range: -10 dBdsx to +6 dBdsx	DSX-1 (RJ-48C) CONNECTION PINOUTS
	Capacity: 1 to 24 DS0s
	Line Codes: AMI, B8ZS	Pin	Name	Description
	DSX-1 interface to PBX
		1	R	Transmit data toward the DTE- Ring
	Framing: D4 (SF) or ESF
		2	T	Transmit data toward the DTE - Tip
	Line Length: 0 to 655 ft and -7.5 dB
		3	—	Unused
	Connector: RJ-48C
		4	R1	Receive data from the DTE - Ring 1
Clock Source	Network, internal, and through
		5	T1	Receive data from the DTE - Tip 1
Diagnostics	Test Pattern Generation and Detection: QRSS, 511, all
		6-8	—	Unused
	ones, all zeros
	Network loopbacks (local and remote); responds to both
	inband and FDL loop codes (T1 interface only)		An optional Dial Backup Interface Module (DIM) is
	Alarm generation and detection		required for dial backup applications.
	Network and user sets of performance data (15 minutes		For a description of the DBU pinouts, refer to the
	and 24 hours)		Quick Start Guide included with your DIM shipment.
Compliance	FCC Part 15 Class A, EN 55022 Class A
	ACTA/FCC Part 68, IC CS-03		Important: For additional details on product features,
	UL/CUL 60950		specifications, installation, and safety, refer to the
Physical	Dimensions: 2.75-inch W x 4.25-inch D		appropriate Hardware Installation Guide on the
	Operating Temperature: 0°C to 50°C		ADTRAN OS System Documentation CD shipped
	Storage Temperature: -20°C to 70°C		with the base unit and available online at
	Relative Humidity: Up to 95 percent, noncondensing		www.adtran.com.

Quick Start Guide, 61200863L1-13D, July 2005 Technical Support 1-888-4ADTRAN (1-888-423-8726) Copyright © 2005 ADTRAN, All Rights Reserved