Installationmanual (this document) x 1 |
|
Sensor detection area adjustment sheet x 1 |
|
Manual for adjusting sensor detection area x 1 | Mounting screws x 2 |
WPrecaution notation
This installation manual uses various symbols for the sake of safe usage.
The results that can occur from ignoring these indications and handling this equipment incorrectly are categorized as follows.
0305@
*Nopower is being supplied from the | Wire the master station correctly to supply power. |
master station. |
|
The wiring is incorrect or a line is open or | Wire correctly. (See "MOUNTINGAND CONNECTION".) |
When you open up the package, make sure all the accessories are present.
Icon display example
@symbol indicates a prohibition. The specific content prohibited is drawn in or near the figure. (For the figure on the left, disassemblyis prohibited.)
Q@ symbol indicates behavior that is mandatory and gives directions.
DThe unit does not operate.
shorted. |
|
'The unit was wired to the master station | Keep the power OFF until the wiring is completed. |
with power supplied. |
|
The master station select switch setting is | Set "A" and "B" correctly. (See "SETTINGS".) |
reversed. |
|
The detection area is not correctly set. | .Check the detection area and camera angle of view area and install so that |
JDW-C
This indicates that ignoring the contents of the warning and handling the equipment
ACAUTIONThis indicates that ignoring the contents of the waming and handling the equipment
people are detected. (See ''ADJUSTMENTS''.) |
incorrectly can result in death or severe injury.
incorrectly can result in personal injury ndor damage to equipment.
People are passing nearly directly under the sensor camera.
Adjust the upldown angle to point down so that they are detected.
ur"t
Do not disassemble or alter.
Do not disassembleor alter this equipment. Doing so would be dangerous. Fire or electric shock could result.
Do not touch the main unit with
Use in areas with water or high humidity is prohibited.
This product is weather resistant, but do not install it in a bathing room or other place with extremely high humidity, any place where water might get into it, or in water. Do not spray water directly on this equipment, for example with a hose. Fire, electric shock, and equipment damage could result.
People are coming directly at the camera.
BThe system does not detect people.
The detection area is cut offby glass.
.This is not a breakdownt. Because of the characteristicsof a heat ray type sensor, it may have difficulty detectingpeople coming directly at the camera. As much as possible, install in such a way that people cut across the detection area. (See "ADJUSTMENTS".)
*Connectan external sensor in "OR mode" so that people cut across the detection area. (See "SETTINGS".)
This is not a breakdown. A heat ray type sensor cannot detect objects through glass. Install in a place where the detection area is not cut off by the glass. (See "MOUNTINGAND CONNECTION".)
\Wall gasket
Electric shock caution
damp or wet hands. Electric shock and equipmentdamage could result. When existing chime wiring
is used, it is possible that it containsA AC power. This can cause
Install securely.
Install securely to a solid location
so that the equipment can not drop Q from its own weight. Equipment
With the external sensor input function in | This is not a breakdown. Set the detection area for each sensor so that people |
"AND mode", people are only detected | are detected by both sensors. (See "SETTINGS".) |
by the main sensor or by the external |
|
sensor but not by both. |
|
Main unit cover
Camera window
Be carefulnot to soil or damage.
equipment damage and electric shock. Have the installation done by an electrical contractor,low voltage contractor,or qualified personnel.
falling could result in injury.
*The internal sensor switch is "OFF".
@Sound cannot be The speaker select switch is "OFF". heard from the 'The master station select switch is "B" unit.
The wiring is incorrect or a line is open or |
Switch "ON" the internal sensor switch.
Switch "ON"the speaker select switch.
Wire correctly. (See " M 0 U " G AND CONNECTION".)
\I | Sensor |
|
Operation | ! CAUTION |
|
4display window | rADo not touch the sensor7or the reflectwe | |
I | 1 mirror. | I |
Notice
This product detects a person, provides notice, and shoots images. It is not an
-Installation precautionsA
HFor correct installation
Do not install in the following places.
\
@Sound cannot be shorted. | ||
heard from the | The mic. sensitivityvolume is at the | |
master station. | ||
"Low" side. | ||
| ||
@There is | The sensor camera is installed too close | |
to the master station. | ||
howling. | ||
| ||
| There is a dog or cat or other small | |
| animal in the detection area. | |
@The sensor is |
| |
detecting but | There is somethingthat moves in the | |
the detected | ||
detection area, for example a flag or tree | ||
objects are not | ||
blowing in the wind, or there are sudden | ||
displayed on the | ||
temperaturechanges. | ||
screen. | ||
| ||
| The external sensor area does not match | |
| the camera angle of view. |
Turn the mic. sensitivityvolume to the "High' side. (See "SE'ITINGS".)
This is not a breakdown. Install the sensor camera farther from the master station or turn the mic. sensitivityvolume to the "Low" side until there is no howling.
Set the sensor sensitivity switch to "L (Low)". (See "SETTINGS".)
Recommend to connect an external sensor and use it in "AND mode". (See "SETTINGS'.)
Set the sensor sensitivity switch to "L (Low)". (See ''SETTINGS''.)
*Eithermove the moving object or the object causing the sudden temperature changes outside the detection area or change the area setting. (See "SETTINGS'.)
.Align the external sensor area and the camera angle of view. (See "ADJUSTMENTS' and "SETTINGS".)
Power
Operatingtemperature range Storage temperature range Operating humidity range Picture element
Camera anale of view (horizontalx vertical) Minimum illumination
Sensor operation display light Sensor detection method Sensor detection area Sensor detection speed Sensor sensitivitv switchina Sensor startuD time
SuDDlied from the master station
85% (max.)
Lights up green when the sensor detects something (Can be switched OFF with the select switch) Heat ray type
Max. 5 meters, approx. 70"
0.3 - 1.5 mlsec.
Switchable among three levels H (high), M (medium), and L (low) Amrox. 30 sec. after Dower comes on
Any place blown on by a fan, the | 4ny place where sunlight gets in | 4ny place too close to | Any unstable place subject to |
outdoor unit of an | he angle of view of the sensor | luorescent lamps or directly | vibration or mechanical shock. |
or any other place subject to | :amera directly or indirectly. | 'acing powerful illumination. |
|
sudden temperature changes. |
|
|
|
|
|
| / |
| The wiring is incorrect or a line is open or | |
@The picture is | shorted. | |
dark, blurred, or | The camera window is dirtv. | |
not displayed at | The outside temperature dropped | |
all. | ||
suddenly and the camera window has | ||
| ||
| fogged up. | |
@There are | There is a bright light source in the | |
lines on the | camera angle of view. | |
screen. |
|
white@The screen is There is a fluorescent lamp nearby. flickering.
Check the wiring and wire correctly. (See "MOUNTINGAND CONNECTION'.)
Clean the lens with lens cleaner or with a clean, soft, damD cloth.
When the temperaturesinside and outside the product even out, the camera window returns to normal.
*Eitherremove the light source, adjust the angle so that the light does not come into the angle of view, or change the mounting location of the main unit. (See "ADJUSTMENTS".)
This is not a breakdown. Block out the light from the fluorescent lamp.
Externalsensor input Internal sensor switching Internal speaker Internal mic.
Master station switch
Camera
Angle adjustmentrange
Sensor
InstallationDlaces
Protective structure
Weight
Dimensions (mm)
An external sensor can be connectedand operated in either an "AND" or "OR" configuration with this unit. The internal body detection sensor can be controlled to be "ON"or "OFF".
The internal speaker can be controlled to be "ON"or "OFF" with the speaker select switch. The mic. sensitivitv can be adiusted with the mic. sensitivitv volume.
Switchable accordina to the master station version.
k50"leftlright,
(The IeWright and up/down angles can both be changed in incrementsof 5".) k50"leftlright,
(The left/riaht angle can be changed in increments of 10" and the uddown angle in increments of 5 O . I Indoors/Outdoors
102 (W) x 182 (H) x 94 (D)
On any surface that moves or is | 4ny place too close to a source | Any place where the detection | In or near any place subject to |
affectedby wind. | If electrical noise, for example a | area or camera angle of view will | steam or oil from an exhaust |
| xoadcasting station or wireless | be blocked off. | duct. |
| station of any kind. |
|
|
-Connection precautionsA
.Use | two conductor wire from the |
.When | using two cameras, always use one two conductor wire for each camera. If you connect two cameras with one multi- |
conductor wire, the cameras may not operate correctly.
@If the wiring is routed together with high voltage AC wiring, other power wiring, wiring for electrical lights, and telephone lines, this can disrupt the picture and sound quality and cause malfunction. Either use separate conduits or run wires in separate paths from each other.
.When existing wiring is used, for some type of wiring, this system may not operate correctly. Changing the wiring restores normal operation.
Aiphone warrants its products to be free from defects of material and workmanship under normal use and service for a period of two years after delivery to the ultimate user and will repair free of charge or replace at no charge, should it become defective upon which examination shall disclose to be defective and under warranty. Aiphone reserves unto itself the sole right to make the final decision whether there is a defect in materials and/or workmanship; and whether or not the product is within the warranty. This warranty shall not apply to any Aiphone product which has been subject to misuse, neglect, accident, or to use in violation of instructions furnished, nor extended to units which have been repaired or altered outside of the factory. This warranty does not cover batteries or damage caused by batteries used in connection with the unit. This warranty covers bench repairs only, and any repairs must be made at the shop or place designated in writing by Aiphone. Aiphone will not be responsible for any costs incurred involving on site service calls.