3

Drain Control

Operates Drain, and used to set Cooling Water Flow Rate

4

Set

Preset Run Time and Distillation Control Temperature

5

Increase button

6

Decrease button

7

C/F & Enter

Enter Key. Also change from Fahrenheit to Centigrade

8

Time display

Displays the remaining time of the boiler operation

9

Temp display

Displays the detected temperature of distillation column

10

L1

Beer Input pump operating

11

L2

Cooling water inlet in operation

12

L3

Indicator LED for draining green is for auto drain, red is for

 

 

manual drain

13

L4

Overheat Indicator

14

L5

Tank Overheat Indicator. Red means the boiler was cut off

 

 

as the heating elements are too hot (usually because of a

 

 

lack of beer input)

15

L6

Cooling water proportional valve operation indicator

16

L7

Indicates the detected temperature is lower than the preset

 

 

temperature and boiler is heating.

17

L8

Indicates the detected temperature is higher than the

 

 

preset temperature and the boiler is in idle mode.

Chapter Three: Installation

 

Disconnect all power before installation.

If the boiler is installed in an inaccessible place, ensure that the electrical power, beer supply, and water supply can be easily turned off in an emergency.

The minimum water inlet pressure is 3.6 psi (0.25 bar) and the maximum is 30 psi (2 bar), for pressures in excess of this, use an inline pressure regulator before connecting to the boiler system.

The steam pipe from the boiler to still should be kept to a minimum, pipes longer than 10 feet (3 meters) should be insulated to prevent heat loss. Steam pipes will be hot during use and must be protected against accidental contact.

Keep the number of right angle bends to a minimum and ensure that the run of does not create a trap into which condensate would gather and cause a blockage (i.e. the pipe must not go down and then up).

There must be no valve or other blockage in the steam pipe

The steam pipe should be metal of other material that can withstand a constant 350 degrees F (150°C) temperature. Stainless Steel or Copper pipe is recommended. Do not use pipe that can rust.

Do not permanently install the EB120 system outdoors. It can be used outdoors, but must be stored inside and protected from the weather. The unit is not weatherproof.

Do not use the EB120 inside your house. A garage with the door open is fine, but never inside the living area.

The EB120 should be level side-to-side and front to back and should be installed so that the arrows on the case point up.

Do not install or operate the EB120 in close proximity to flammable or hazardous substances.

EB120 Advanced Ethanol Boiler

5

Page 5
Image 5
Allard EB120 manual Chapter Three Installation

EB120 specifications

The Allard EB120 is a distinctive sports car that hails from the Swedish automotive company Allard. Renowned for its performance-oriented design and powerful heritage, the EB120 captures the essence of classic European sports cars while integrating modern technology and engineering. This unique vehicle stands out not only for its sleek aesthetics but also for its impressive specifications.

Under the hood, the EB120 is powered by a robust engine that delivers exhilarating performance. Equipped with a 5.0-liter V8 engine, the car produces an impressive output, allowing it to accelerate from 0 to 60 miles per hour in a matter of seconds. The engine is finely tuned to provide a seamless driving experience, striking a perfect balance between power and efficiency.

One of the key features that define the EB120 is its lightweight construction. The chassis is designed using advanced materials, including reinforced steel and carbon fiber, which contribute to the car’s agility and responsiveness. This combination not only enhances performance but also improves fuel efficiency, making the EB120 a practical choice for enthusiasts who desire speed without compromising on economy.

The Allard EB120 also boasts cutting-edge aerodynamics, with a streamlined profile that minimizes drag and maximizes downforce. This design aspect not only enhances stability at high speeds but also contributes to improved handling and cornering capabilities. The car is equipped with an advanced suspension system, featuring adjustable dampers that allow drivers to customize their ride based on personal preferences and driving conditions.

In terms of technology, the EB120 incorporates modern infotainment systems that keep drivers connected and entertained. The interior is designed with luxury and comfort in mind, featuring high-quality materials and ergonomic seats. State-of-the-art sound systems and intuitive controls ensure that every journey in the EB120 is enjoyable.

Safety features are also a priority, with multiple airbags, advanced braking systems, and traction control systems that work seamlessly to provide a secure driving experience. The Allard EB120 is not just about speed; it is a well-rounded vehicle that considers the holistic needs of the driver and passengers.

In summary, the Allard EB120 is a remarkable sports car characterized by its powerful V8 engine, lightweight construction, and advanced aerodynamics. A blend of luxury and performance, it represents a significant achievement in automotive engineering, appealing to both traditional car enthusiasts and modern drivers alike.