|
|
|
| Operation | |
|
|
|
| ||
| Display Indications |
| |||
Display | Meaning | Display | Meaning | ||
FC 5 | Program identification code (ROM). This |
| HFIL | Hot fill | |
is an example only. | Lo | Low water level | |||
| |||||
|
|
|
| ||
Hold | Wait...power has just been turned on. | ned | Medium water level | ||
|
|
|
| ||
PAY/(price)* | Pay (flashes alternately with start price if |
| HI | High water level | |
“FLSH” SETUP option is enabled) | SUP0 | No supplies | |||
| |||||
|
|
|
| ||
CY | Cycle (followed by | SUP1 | Supply 1 | ||
|
|
|
| ||
tESt/CYC* | Test cycle selected. | SUP2 | Supply 2 | ||
|
|
|
| ||
FAr | Degrees Fahrenheit | SUP3 | Supply 3 | ||
|
|
|
| ||
CEL | Degrees Celsius | SUP5 | Supply 5 (Supply 1 and 2) | ||
|
|
|
| ||
Heat | Auxiliary heat enabled. | SUP6 | Supply 6 (Supply 2 and 3) | ||
|
|
|
| ||
noHt | Auxiliary heat disabled. | drAI/dISt* | Distribution (load balancing before extract) | ||
|
|
|
|
| |
FLSH | Flashing vend price enabled. | drAI/For* | Drain step (low speed forward in test | ||
cycle) | |||||
|
|
|
| ||
|
|
|
| ||
nFLS | Flashing vend price disabled. | SPIn/tInE* | Reads “SPIn” for one second, then | ||
|
|
| “tI nE” followed by time for spin. | ||
Strt/Ant* | Start |
| |||
| |||||
showing vend price in SETUP mode | SdLY | Spin coast delay | |||
| |||||
|
|
|
| ||
Con1/deno* | Coin 1 |
| STOP | Stop routine | |
showing value of coin 1 in SETUP mode | donE | Cycle and stop routine have ended. | |||
| |||||
|
|
|
| ||
Con2/deno* | Coin 2 |
| HI 1 | Low spin in test cycle. | |
showing value of coin 2 in SETUP mode | HI 2 | High spin in test cycle. | |||
| |||||
|
|
|
| ||
PrE | Prewash segment (1st of 8 segments) | bAL/FAIL* | Balance routine failed during test cycle. | ||
|
|
|
| ||
UASH | Wash segment (2nd of 8 segments) | SHUT/door* | Door not properly closed. | ||
|
|
|
| ||
FIL1 | First fill (3rd of 8 segments) | CANt/OPEN* | Computer cannot unlock door after five | ||
FIL2 | Second fill (4th of 8 segments) | attempts. | |||
| |||||
|
|
|
| ||
FIL3 | Third fill (5th of 8 segments) | FILL/STOP* | Programmed water level not reached after | ||
FIL4 | Fourth fill (6th of 8 segments) | 30 minutes. | |||
| |||||
|
|
|
| ||
FIL5 | Fifth fill (7th of 8 segments) | FULL | The computer detects low water level or | ||
FIL6 | Sixth fill (8th of 8 segments) | higher when none should be present. | |||
| |||||
|
|
|
| ||
AFIL | Auxiliary fill | dFLt | Drive fault detected. | ||
|
|
|
| ||
bFIL | Warm fill (both hot and cold) |
| Temperature sensor failure or temperature | ||
|
|
|
| ||
CFIL | Cold fill | tSFL | |||
out of range. | |||||
|
|
|
| ||
bLCH | Add bleach |
| |||
|
| ||||
*Display indications separated by a slash represent an alternating display.
15
F232061