
Operation
Table 2 lists the various displays and what they mean. The operator should become familiar with these computer displays.
Display Indications
Display | Meaning | Display | Meaning | |
|
|
|
| |
vv01 | Program identification code (ROM) | SPC? | Special test cycle function (if present, ignore) | |
Example only. |
|
| ||
Lo | Low water level | |||
|
| |||
|
|
|
| |
Hold | Wait...power has just been turned on. | nEd | Medium water level | |
CY | Cycle (followed by | HI | High water level | |
|
|
|
| |
tESt/CYC* | Test cycle selected. | SUP1 | Supply 1 | |
|
|
|
| |
FAr | Degrees Fahrenheit | SUP2 | Supply 2 | |
|
|
|
| |
CEL | Degrees Celsius | SUP3 | Supply 3 | |
|
|
|
| |
HEAt | Auxiliary heat enabled. | SUP4 | Supply 4 | |
|
|
|
| |
noHt | Auxiliary heat disabled. | SUP5 | Supply 5 (SETUP option) | |
|
|
|
| |
tFIL | SUP6 | Supply 6 (supply 1 and 5) | ||
|
|
|
| |
ntFL | SUP7 | Supply 7 (supply 3 and 4) | ||
|
|
|
| |
CooL | Automatic | SLo/For** | Gentle wash speed, forward direction | |
|
|
|
| |
noCL | Automatic | SLo/rEv** | Gentle wash speed, reverse direction | |
|
|
|
| |
Ag 1 | Agitation 1 selected (90% agitation). | norn/For | Normal wash speed, forward direction | |
Ag 2 | Agitation 2 selected (33% agitation). | norn/rEv | Normal wash speed, reverse direction | |
Ag 3 | Agitation 3 selected (10% agitation). | drAI | Drain enabled. | |
|
|
|
| |
Ag 4 | Agitation 4 selected (6.7% agitation). | nodr | Drain disabled. | |
|
|
|
| |
AgSn | Agitation speed normal | dISt | Distribution (load balancing before extract) | |
|
|
|
| |
AgSL** | Agitation speed low | SPIn/tInE* | Reads “SPIn” for one second, then “tInE” followed by | |
|
| time for spin. | ||
PUnP | Pump output enabled (future use only). | |||
|
| |||
nPnP | Pump output disabled (future use only). | SPn1 | Lowest of three spins | |
PrE | PreWash segment (1st of 11 segments) | SPn2 | Middle of three spins | |
|
|
|
| |
UASH | Wash segment (2nd of 11 segments) | SPn3 | Highest of three spins | |
|
|
|
| |
FIL1 | First fill (3rd of 11 segments) | STOP | Stop routine | |
|
|
|
| |
FIL2 | Second fill (4th of 11 segments) | SdLY | Spin coast delay | |
|
|
|
| |
FIL3 | Third fill (5th of 11 segments) | donE | Cycle and stop routine have ended. | |
|
|
|
| |
FIL4 | Fourth fill (6th of 11 segments) | dFLt | Drive fault detected. | |
|
|
|
| |
FIL5 | Fifth fill (7th of 11 segments) | door | Door not properly closed. | |
|
|
|
| |
FIL6 | Sixth fill (8th of 11 segments) | BAL/door* | Indicates vibration switch or door locked switch tripped | |
|
| during spin. | ||
FIL7 | Seventh fill (9th of 11 segments) | |||
|
| |||
|
|
|
| |
FIL8 | Eighth fill (10th of 11 segments) | FILL/STOP* | Programmed water level not reached after | |
|
| 30 minutes. | ||
FIL9 | Ninth fill (11th of 11 segments) | |||
|
| |||
|
|
|
| |
CFIL | Cold fill | FULL | The computer detects low water level or higher when | |
|
| none should be present. | ||
bFIL | Warm fill (both hot and cold) | |||
|
| |||
|
|
|
| |
HFIL | Hot fill | tSFL | Temperature sensor failure or temperature out of range. | |
|
|
|
| |
AFIL | Auxiliary fill (SETUP option) | bAL? | Special test cycle function (if present, ignore) | |
|
|
|
|
* Display indications separated by a slash represent a flashing display.
** The
Table 2
12 | © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT | F232183 |