
Media Converter Installation Guide
Converteon Enclosures
This product is supported in all four Converteon enclosures:
Related Documents
DIP Switch 4
SW1 |
|
|
|
|
|
| ||
4 |
|
|
|
|
|
|
| 1 |
|
|
|
|
|
|
| ||
| 4 |
| 3 |
| 2 |
| 1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ON OFF
DIP Switch 1
Off
On
Overview
The
| IEEE 802.3u | |
Pair Port | | Half- or |
| ||
| | |
| | |
| IEEE 802.3x flow control at 10, 100, or 1000 Mbps | |
|
| |
SFP Slot | Supports | |
| module sold separately.) | |
|
|
|
Operating Modes | | Link Test |
| | MissingLink™ |
| | Smart MissingLink |
| The operating modes can be activated with or without support | |
| for Operations, Administration, and Maintenance. | |
|
|
|
Operations, Administration, and | | Loopback test* |
Maintenance (OAM) Features | | Remote Converteon line card management* |
| ||
| Remote management software downloads* | |
| | Dying gasp** |
| | Variable requests* |
|
|
|
Other Features | | Jumbo frames up to 10,240 bytes |
| Ingress and egress packet rate limiting* | |
| Operating mode and port status LEDs | |
| | Low power mode |
| | Cyclical redundancy check |
| Suitable for managed and unmanaged network | |
|
| environments |
| Management available with the | |
|
| Card |
| | |
|
|
|
(* Requires the
(** Requires the
Note
This line card cannot be managed with the
|
1
For background information on the Converteon products, refer to the Converteon
Verifying the Package Contents
The following items should be in the shipping container:
One
This Installation Guide
Warranty card
If any item is missing or damaged, contact your Allied Telesis sales representative for assistance. You should retain the original shipping material in case you need to return the
unit to Allied Telesis.
Caution
The media converter line card is sensitive to and can be damaged by electrostatic discharge. Wear a grounding device and observe electrostatic discharge precautions when installing the card in the chassis.
Reviewing Safety Precautions
Before installing the media converter, review the safety precautions detailed in the Converteon chassis’ Installation Guide.
Cable Specifications
The cable specifications for the
Speed | Cable Type | Maximum Operating | |
Distance | |||
|
| ||
|
|
| |
|
|
| |
10 Mbps | Standard TIA/EIA | 100 m (328 ft) | |
| better shielded or unshielded cabling with 100 ohm |
| |
| impedance and a frequency of 16 MHz. |
| |
|
|
| |
100 Mbps | Standard TIA/EIA | 100 m (328 ft) | |
| TIA/EIA |
| |
| (Cat 5e) shielded or unshielded cabling with 100 |
| |
| ohm impedance and a frequency of 100 MHz. |
| |
|
|
| |
1000 Mbps | Standard TIA/EIA | 100 m (328 ft) | |
| TIA/EIA |
| |
| (Cat 5e) shielded or unshielded cabling with 100 |
| |
| ohm impedance and a frequency of 100 MHz. |
| |
|
|
|
For the fiber optic cable specifications, refer to the SFP module instructions.
Setting the Operating Mode
There are DIP switches on the line card for setting the card’s operating mode. You can also set the operating mode with the optional
2
1447
SW1 |
|
|
|
|
4 |
|
|
| 1 |
4 | 3 | 2 | 1 | OFF |
|
|
|
| ON |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 1446 |
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Operating Mode | Switch 4 | Switch 3 | Switch 2 |
|
| Switch 1 | ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Link Test (default setting) | Off | Off | Off |
|
| Off | ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
MissingLink | Off | Off | Off |
|
| On | ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Smart MissingLink | Off | Off | On |
|
| Off | ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Link Test with OAM | Off | On | Off |
|
| Off | ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
MissingLink with OAM | Off | On | Off |
|
| On | ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Smart MissingLink with OAM | Off | On | On |
|
| Off | ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Installing the Media Converter
Note
The media converter supports hot swapping and can be installed while the chassis is powered on.
To install the media converter:
1.Remove the slot cover from one of the slots in the Converteon chassis by loosening the captive screw with a Phillips head screwdriver. The unit can be installed in any of the media converter slots.
257 |
Note |
Retain the slot cover and reinstall it if you ever remove the line card. An open slot allows dust to enter the unit and reduces proper airflow in the chassis.
2.Align the edges of the line card with the guides in the slot and carefully slide the card into the chassis until it is flush with the front of the chassis. Light pressure may be needed to seat the module on the connector on the backplane in the chassis.
3