Allstar Products Group MVP-831ERECEIVER WIRING INSTRUCTIONS, Receiver Programming Instructions

Learn/Erase Button

Indicator LED

MVP-831E RECEIVER WIRING INSTRUCTIONS

IMPROPER WIRING COULD CAUSE ELECTROCUTION OR WARNING DAMAGE TO CIRCUITRY. FOLLOW LOCAL BUILDING AND ELECTRICAL CODES.

TO PREVENT ELECTROCUTION DISCONNECT POWER AT

WARNING

FUSE BOX AND DOOR OPENER BEFORE WIRING

PERMANENTLY.

The MVP-831E receiver functions as a 3-button

106548

station. Three sets of isolated contacts are provided;

normally open contacts for the OPEN

PUSHBUTTON (orange wires); normally open

contacts for the CLOSE PUSHBUTTON (black

wires); normally closed contacts for the STOP

PUSHBUTTON (gray wires). Refer to Figure 1.

For special STOP circuit applications, normally

D

open contacts are available from the factory.

R

E

H

I T

E

W

24 VAC

Typical 4-wire 3-button stations are wired as shown

BL

in Figure 2. Number 18 gauge wire or heavier must

O

ACK

be used for wiring the control stations and the MVP-

A

R

G

831E receiver to the door operator. Smaller gauge

N

R

Y

E

G

A

wire may cause operational problems, especially

Figure 1

OPEN

when

multiple 3-button

stations are

used.

For

typical

installations the

MVP-831E

receiver is

CLOSE

STOP

mounted near the door operator, away from any high

voltage conduits or steel

support beams.

For

wiring, follow the steps below and refer to Figure 3.

106549

Step 5

				WALL PUSH
	Step 3			BUTTON
		COMMERCIAL		STATION
MVP-831E		OPERATOR		OPEN
				Step 4
RECEIVER
		STOP COM	OPEN CLOSE	CLOSE
				STOP
				COMMON
	ORANGE
	BLACK
	GRAY
	BLACK
	GRAY	Step 2		Figure 3
	ORANGE
RED WHITE			Removed Wire
			(See Step 1)
24 VAC	Step 6

RECEIVER PROGRAMMING INSTRUCTIONS

Learning Transmitter Codes

The MVP-831E receiver is capable of learning the codes from up to 8 different Allstar Open/Close/Stop transmitters. The transmitters may be any combination of Allstar’s MVP, Classic or original dip- switch type Open/Close/Stop transmitters

WALL PUSHBUTTON STATION

105113

OPEN	TERMINALSTRIP
OPERATORTO
CLOSE
STOP

Figure 2

1.In the door operator control panel, locate the wire connecting the door operator to the 3-button station COMMON. Note its location and remove.

2.Connect one of the gray wires from the MVP-831E to the wire just removed from the pushbutton COMMON.

3.Connect the following wires from the MVP-831E to the operator 3-button COMMON (as shown in Figure 3):

ONE ORANGE (OPEN)

ONE BLACK (CLOSE)

ONE GRAY (STOP)

4.Connect the remaining MVP-831E black wire to the CLOSE pushbutton terminal in the door operator control panel.

(Models 8833-O/C/S, 8833C-O/C/S, 831, 733, 639, and/or 53S).

Match the receiver operating frequency with the transmitter operating frequency. Pre-program the transmitter (or set the DIP switches) according to the instructions that accompanied the transmitter.

For transmitters that can operate multiple doors (Models 8833C-O/C/S, 733 639, and 53S), make sure the selector switch(es) is (are) positioned for the desired door you want to operate before starting the receiver programming steps below.

Programming The Receiver

Step 1: Momentarily press and release the Learn button. The LED will turn on.

Erasing the Receiver’s Memory

Step 1: Press and HOLD the Learn button. The indicator LED will turn on.

Step 2: When the LED turns off (after approximately 5 seconds), release the Learn button.

5.Connect the remaining MVP-831E orange wire to the OPEN pushbutton terminal in the door operator control panel.

6.Finish the wiring by connecting 24 VAC to the red and white wires of the MVP-831E receiver.

BEFORE APPLYING POWER, CHECK ALL CONNECTIONS AND INSTALL THE

ANTENNA.

Step 2: Using a programmed transmitter, press any one of the transmitter buttons (OPEN, CLOSE, or STOP). When the receiver learns the transmitter code, the LED will turn off. The receiver has automatically learned the two remaining buttons.

Step 3: Repeat to add additional transmitters with different codes if desired.

Important

Refer to individual manuals for

transmitter installation, coding and

user instructions.

Page 2 of 4 DOC. 112049 REV A Page 3 of 4 DOC. 112049 REV A