INTERFACES
position of the image can be adjusted through the Horizontal Position Control knob located on the front panel. Similarly, one can only adjust the position of the image on the display for Input 2 using the Horizontal position control knob when the CH2 Horizontal Delay switch is in the OFF position.
7.3 I.D. BIT SWITCH 1& 2
Many computers use ID Bits or “Sense Pins” to recognize that a monitor has been connected to its video output port. Often, these ID Bits will allow the computer to recognize what type of monitor is connected in terms of its scan rate compatibility. When the ID Bit switch is in the ON position, the VA6831FC allows the main ID Bit (pin 4 on the input connector) to be connected to the Ground signal.
This is used primarily when interfacing laptop computers to imitate the presence of a local monitor. Typically, this recognition will take place during the boot up stage. If your Interface does not output video on the display, then place this switch in the ON position and reboot the computer. When left in the OFF position, this ID Bit will be passed through to the local monitor output port.
ACCESSORIES | 8 | ||
|
|
|
|
Model No. |
| Description |
|
|
|
| |
| RACK MOUNT ACCESSORIES |
| |
DA1293SX | Rack/Wall Shelf fits two VA6831FC |
| |
| units side by side |
| |
DA1294SX | Rack/Wall mount ears for single |
| |
| VA6831FC |
| |
| TABLE MOUNT BRACKETS |
| |
TM1271 | 1U | High, ½ |
|
TM1272 | 1U | High, ½ |
|
| HD connector plate |
| |
TM1273 | 1U | High, ½ |
|
| connectors |
| |
TM1274 | 1U | High, ½ | |
| POWER connectors |
| |
Input cable Local Monitor Cables and Output Cables must be ordered separately from following list.
Model No. | Description |
|
|
| INPUT/LOCAL MONITOR CABLES |
MS8121CA | MAC Local Monitor Cable |
MS8122CA | MAC Input Cable |
MS8123CA | SUN/SGI Local Monitor Cable |
MS8124CA | SUN/SGI Input Cable |
MS8125CA | VGA Local Monitor Cable |
MS8126CA | VGA Input Cable |
MS8129CA | 5 BNC Input/Local Monitor Cable |
| 4 BNC TO 4 BNC COAXIAL CABLE |
CB4103MR | 3 feet, 4 BNC to 4 BNC coaxial cable |
CB4106MR | 6 feet, 4 BNC to 4 BNC coaxial cable |
CB4112MR | 12 feet, 4 BNC to 4 BNC coaxial |
| cable |
CB4125MR | 25 feet, 4 BNC to 4 BNC coaxial |
| cable |
CB4150MR | 50 feet, 4 BNC to 4 BNC coaxial |
| cable |
CB4175MR | 75 feet, 4 BNC to 4 BNC coaxial |
| cable |
CB41100MR | 100 feet, 4 BNC to 4 BNC coaxial |
| cable |
CB41150MR | 150 feet, 4 BNC to 4 BNC coaxial |
| cable |
| 5 BNC TO 5 BNC COAXIAL CABLE |
CB4203MR | 3 feet, 5 BNC to 5 BNC coaxial cable |
CB4206MR | 6 feet, 5 BNC to 5 BNC coaxial cable |
CB4212MR | 12 feet, 5 BNC to 5 BNC coaxial |
| cable |
CB4225MR | 25 feet, 5 BNC to 5 BNC coaxial |
| cable |
CB4250MR | 50 feet, 5 BNC to 5 BNC coaxial |
| cable |
CB4275MR | 75 feet, 5 BNC to 5 BNC coaxial |
| cable |
CB42100MR | 100 feet, 5 BNC to 5 BNC coaxial |
| cable |
CB42150MR | 150 feet, 5 BNC to 5 BNC coaxial |
| cable |
All MS81 Series cables listed above are 3 ft. long. These cables are available in 6 ft. and 12 ft. lengths. Please call
9
