American DJ Roto-Balls General Operation, Fuse Replacement, Lamp Replacement

Roto-Balls™ Unpacking

Every Roto-Balls™ has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for any damage and be sure all literature has arrived intact. In the case damage has been found or parts are missing, please contact our toll free customer support number for further instructions.

Roto-Balls™ Features

•104 Vibrantly Colored Beams.

•10 RPM Motor.

•Easy Lamp Replacement.

•Air Cooled.

•Light Weight, Compact Case Design.

•Built-In Mounting Plate.

•Bright LL-200 or LL-200/2 (200 Watt Lamp).

•Low Power Consumption.

Roto-Balls™ Warranty Card

The Roto-Balls™ carries a 90 day limited warranty. We recommend you fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. If the unit is under warranty, you must provide a copy of your proof of purchase invoice. Please contact American DJ® customer support for a R.A. number.

Roto-Balls™ Operation

General Operation:

Simplicity! Just plug this light in, and watch it go. This fixture is designed to operate as a stand alone unit, there is no need of a controller. The Roto-Balls™ is ready to be plugged in, out of the box. There is no power switch, after plugging the unit the unit will light up and rotate in a single direction, while the twin balls also rotate. If there is no lamp output, please check the fuse and bulb as they sometimes become loose during shipping. If the fuse and bulb are good, please contact customer support for further instructions.

Roto-Balls™ Power Supply

Power Supply: Before plugging your unit in, be sure the source volt- age in your area matches the required voltage for your American DJ® Roto-Balls.™ The American DJ® Roto-Balls™is available in a 120v and 220v version. Because line voltage may vary from venue to venue, be sure to plug your fixture into a wall outlet with a matching power supply before attempting to operate.

Roto-Balls™ Fuse & Lamp Replacement

Caution: Always replace with the exact same type lamp and fuse, unless otherwise specified by an authorized American DJ® technician. Replace with anything other than the specified part can damage your unit and will void your manufactures warranty.

Fuse Replacement:

Disconnect the unit’s main power supply. Insert a standard flat head screw driver in to the fuse holder housing. Turn the screwdriver in counter-clockwise direction to remove the fuse holder. Remove the old fuse and discard it, replace the fuse with the same type. Insert the fuse holder back into it’s housing and turn in clockwise direction to lock the holder in place.

Lamp Replacement:

Caution! Never open the unit when in use. Always disconnect the main power and allow the fixture ample time to cool before attempting to replace the lamp. Lamp replacement has been made simple by incorporating a split dome that is retained by thumb screws. Again, please remember to always replace with the exact same type lamp.

1.Be sure to follow the proper procedures when handling halogen lamps. Never touch the new lamp with your bare fingers.

2.Remove the three thumb screw that secure the upper half of the dome to the lower.

3.Carefully pull up the upper half of the dome to expose the lamp.

4.Remove and replace the lamp.

5.Reassemble in reverse order.

If after you have replaced the lamp or fuse and you continue to blow either one, STOP using the unit. Contact customer sup- port for further instructions, you may have to return the unit for servicing. Continuing to use the unit may cause serious damage.

©American DJ Supply® - www.americandj.com - Roto-Balls™ Instruction Manual Page 3 ©American DJ Supply® - www.americandj.com - Roto-Balls™ Instruction Manual Page 4