American Dryer Corp AD-120ES III

SECTION VIII

DATA LABEL INFORMA TION

A. DATA LABEL

Contact American Dryer Corporation

When contacting American Dryer Corporation, certain information is required to insure proper service/parts

information from ADC. This information is on the data label located on the left side panel/wall area behind the

control door. When contacting ADC, please have the model number and serial number available.

Contents

Main AD-120ES III (Extended Side Panels) Installation Manual Retain This Manual In A Safe Place For Future Reference Important AD-120ES III Page Page Table of Contents Page SECTION I IMPORTANT INFORMATION IMPORTANT: The dryer must be transported and handled in an upright position at ALL times. A. RECEIVING AND HANDLING B. SAFETY PRECAUTIONS Page SECTION II SPECIFICATIONS/COMPONENT IDENTIFICATION Steam A. SPECIFICATIONS Gas Specifications ADG-120ES III ADE-120ES III ADS-120ES III B. COMPONENT IDENTIFICATION Page SECTION III INSTALLATION PROCEDURES A. LOCATION REQUIREMENTS IMPORTANT: The dryer must be installed on noncombustible floors only . IMPORTANT: Dryer should be located where a minimum amount of exhaust duct will be necessary. B. UNPACKING/SETTING UP IMPORTANT: The dryer must be transported and handled in an upright position at ALL times. WARNING THIS EXHAUST DUCT TRANSITION PIECE MUST BE INSTALLED FIRST! C. DRYER ENCLOSURE REQUIREMENTS D. FRESH AIR SUPPLY REQUIREMENTS E. EXHAUST REQUIREMENTS Page Page Page Page Page F. ELECTRICAL INFORMATION ADG-120ES III Reversing, 3 (GAS) ADS-120ES III Reversing, 3 (STEAM) ELECTRIC AL S ERVI C E S PECIFI C A TIO NS (P ER DR YER) ADE-120 III (72 kW Electric) Reve r sing, 3 ELECTRICAL SERVICE SPECIFICATIONS (PER DRYER) OVEN SIZE (kW) SERVICE VOLTAGE PHASE WIRE SERVICE APPROX. AMP DRAW NOTE: A CIRCUIT SERVICING EACH DRYER MUST BE PROVIDED. Page G. GAS INFORMATION TYPE OF GAS TYPE OF GAS Page Page H. STEAM INFORMATION Operating Steam Pressure Page COMPRESSED AIR SUPPLY AIR PRESSURE Normal 80 PSI 5.51 bar Minimum Supply 70 PSI 4.82 bar Maximum Supply 90 PSI 6.21 bar Page I. PREPARATION FOR OPERATION J. PREOPERATIONAL TESTS Page K. SHUTDOWN INSTRUCTIONS L. OPERATING INSTRUCTIONS SECTION IV SERVICE/PARTS INFORMA TION A. SERVICE B. PARTS SECTION V WARRANTY INFORMA TION A. RETURNING WARRANTY CARDS B. WARRANTY C. RETURNING WARRANTY PARTS Page SECTION VI ROUTINE MAINTENANCE A. CLEANING SUGGESTED CLEANING SCHEDULE Page B. ADJUSTMENTS C. LUBRICATION SECTION VII TROUBLESHOOTING MICROPROCESSOR CONTROLLER (COMPUTER) MODELS Page Page Page P. No heat (for GAS MODEL ONLY)...ignitor sparks, burner goes on and off right away ... Q. No heat (for STEAM MODELS ONLY)... R. No heat (for ELECTRIC MODELS ONLY)... S. Dryer operates but is taking too long to dry... T. Condensation on main door glass... U. Dryer is making scraping noise at basket (tumbler) area... V. Excessive noise and/or vibration... TIMER MODELS Page ELECTRIC MODELS STEAM MODELS G. Heat unit is not operating for ONLY one (1) temperature selection... H. Dryer operates but is taking too long to dry load... I. Dryer is cycling on hi-limit thermostat (for GAS AND ELECTRIC MODELS ONLY)... J. Condensation on main door glass... K. Dryer is making scraping noise at basket (tumbler) area... L. Excessive noise and/or vibration... Page Page SECTION IX REVERSING TIMER SPIN/DWELL ADJUSTMENTS TIMING LEGEND SECTION X Page SECTION XI BURNER AND BASKET (TUMBLER)/LINT CHAMBER I M P O R T A N T FOR TIMER OR PHASE 5 WITHOUT HEAT FAULT (GAS MODELS ONLY) IMPORTANT I M P O R T A N T FOR TIMER OR PHASE 5 WITHOUT HEAT FAULT (ELECTRIC OR STEAM MODELS ONLY) IMPORTANT