American Power Conversion RS 1000 user manual Contents CON Nect Battery Cartridge, Computer

	®	1	CONTENTS	2 CONNECT BATTERY CARTRIDGE		3 OPERATING ENVIRONMENT
www.apc.com		✔	✔ RJ-11	RJ-11
Back-UPS®RS 1000			✔ USB	RJ-45		32 - 104oF (0 - 40oC)
						✔	24 inches ✔	✘
Back-UPS®RS 1500			®
		✔	✔
							60 cm
User’s Manual
		✔
4 CONNECT EQUIPMENT / POWER			5 CONNECT PHONE/MODEM/FAX		6 CONNECT 10/100 Base-T or VOIP	7 CONNECT INTERFACE CABLE	INSTALL SOFTWARE ON
				Phone Jack		For connection of APC’s optional	10 COMPUTER

external 24-volt battery pack

(BR24BP) to the Back-UPS RS 1000

and Back-UPS RS 1500.

			Wall
	Wall		Outlet
Outlet		Network Jack

TVSS GND

To Computer USB

Follow the

on-screen

Port

Monitor

Computer

USB

Data Port

instructions.

RJ-45

BR24BP Battery Pack

Network Port

10/100 Base-T

Computer

VOIP

Modem/

Computer

Modem Port

Phone/Fax

NOTE:

Computer

Macintosh Users - for full USB

BATTERY

performance, use OS 9.22 or higher.

BACKUP

If Autoplay is not enabled on the computer,

Printer or Scanner

External Disk or

8 SWITCH ON THE BACK-UPS

9 ORIENTATION

proceed as follows:

OR

CD / DVD Drive

Note: Allow the Back-UPS to charge for a

•

When Self-Test has successfully

1.

On the computer desktop of the display,

SURGE ONLY

full eight (8) hours prior to use.

completed, only the green On Line

2.

double-click on My Computer.

Press the front panel Power ON/OFF switch

indicator will be lit.

Double-click on the CD-ROM drive icon

and follow the on-screen instructions.

and observe that the following events occur

•

If the internal battery cartridge is not

FAX

after pressing and releasing the switch:

connected (see Step 2 above), the green

•

The green On Line indicator flashes.

On Line indicator and red Replace Battery

indicators will light. The Back-UPS will

•

The yellow On Battery indicator lights

✘

✔

✔

also emit a chirping sound.

while a Self-Test is being performed.

11	CONNECT TVSS
	GROUND

STATUS INDICATORS AND ALARMS

SERVICE

The Back-UPS features a transient voltage surge-suppression (TVSS) screw for connecting the ground lead on additional surge suppression devices such as network and data line surge protectors.

Wall

Outlet

From Data Line

TVSS

TVSS GND

Modem/

Phone/Fax

There are four status indicators (lights) on the front panel of the Back-UPS (On Line, On Battery, Overload, and Replace Battery).

On Line

On Battery

Overload

Replace Battery

On Line (green) - is lit whenever utility power is powering the Battery Backup outlets.

On Battery (yellow) - is lit whenever the battery of the Back-UPS is powering equipment connected to the Battery Backup Outlets.

Four Beeps Every 30 Seconds - this alarm is sounded whenever the Back-UPS is running On Battery. Consider saving work in progress.

Continuous Beeping - this alarm is sounded whenever a low battery condition is reached. Battery run-time is very low.

Promptly save any work in progress and exit all open applications. Shutdown the operating system, computer and the Back-

UPS.

Overload (red) - is lit whenever power demand has exceeded the capacity of the Back-UPS.

Continuous Tone - this alarm is sounded whenever the Battery Backup outlets are overloaded.

Circuit Breaker - the circuit breaker button located on the rear panel of the Back-UPS will stick out if an overload condition forces the Back-UPS to disconnect itself from utility power. If the button sticks out, disconnect non-essential equipment. Reset the circuit breaker by pushing the button inward.

Replace Battery (red) - is lit whenever the battery is near the end of its useful life, or if the battery is not connected (see above). A battery that is near the end of its useful life has insufficient run-time and should be replaced.

Chirps for 1 Minute Every 5 Hours - this alarm is sounded whenever the battery has failed the automatic diagnostic test.

If the Back-UPS arrived damaged, notify the carrier.

If the Back-UPS requires service, do not return it to the dealer. The following steps should be taken:

1.Consult the Troubleshooting section to eliminate common problems.

2.If the problem persists, go to http:// www.apc.com/support/.

3.If the problem still persists, contact APC Technical Support.

4.Have the Back-UPS model number, serial number and date of purchase available. Be prepared to troubleshoot the problem with an APC Technical Support representative. If this is not successful, APC will issue a Return Merchandise Authorization (RMA) number and a shipping address.