CADET™
PEDESTAL SINK
VITREOUS CHINA
CADET™ PEDESTAL SINK
•Classic vitreous china lavatory and pedestal
•Rear overflow
•Faucet ledge with generous shelf area
•Supplied with mounting kit
❏0236.411 Faucet holes on 4" (102mm) centers (Illustrated)
❏0236.811 Faucet holes on 8" (203mm) centers
❏0236.111 Center hole only
Nominal Dimensions: 622 x 508 x 889mm
Separate Components:
❏0236.004 Pedestal top - 4" (102mm) centers
❏0236.008 Pedestal top - 8" (203mm) centers
❏0236.001 Pedestal top - Center hole only
❏
Bowl Sizes: 508mm (20") wide 305mm (12") front to back 152mm (6") deep
Compliance Certifications -
Meets or Exceeds the Following Specifications:
• ASME A112.19.2M for Vitreous China Fixtures
To Be Specified: |
|
❏ Color: ❏ White | ❏ Bone ❏ Linen |
❏ Silver | ❏ Fawn Beige ❏ Black |
❏ Faucet: |
|
❏ Faucet Finish: |
|
❏ Supplies: |
|
❏ |
|
508mm
(20)FINISHED
86mm |
|
|
|
|
| 102 mm | WALL | ||
|
|
|
| (4) |
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
191mm
508mm
(20)
|
|
| PEDESTAL |
| |
|
|
| ANCHORING |
| |
|
|
| SCREW HOLES |
| |
|
|
| 8 mm (5/16) DIA. |
| |
|
| 622mm |
|
|
|
|
|
|
|
| |
| 6mm | 305mm REF. |
|
|
|
| (1/4) |
|
|
| |
| (12) |
|
|
| |
|
|
|
|
| |
|
|
|
|
| DRAIN |
|
|
|
|
| CHASE |
|
|
|
| 203mm |
|
8mm (5/16) |
|
| (8) |
| |
DIA. SCREW |
|
|
|
| |
ANCHOR HOLES |
|
|
|
| |
SUPPLIES AS |
|
| 178mm |
| |
|
| (7) |
| ||
| REQUIRED |
|
|
| |
|
|
|
|
| |
|
|
|
|
| |
| WASTE | * | 635mm |
| OPEN |
|
|
| |||
| 889mm | TO | |||
| TAILPIECE |
| (25) | FLOOR | |
|
|
| (35) | ||
|
| *533mm |
|
| |
FINISHED |
|
|
|
| |
FLOOR | 203mm |
|
| ||
| (8) |
|
|
|
|
203mm | PEDESTAL | |
SIDE SECTION | ||
(8) | ||
|
NOTES:
*DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TRAPS ARE SUGGESTED.
▼ PEDESTAL ANCHORING SCREWS NOT INCLUDED.
■ SUITABLE FOR REINFORCEMENT ONLY. ACTUAL DIMENSIONS MUST BE TAKEN FROM FIXTURE.
FITTING NOT INCLUDED AND MUST BE ORDERED SEPARATELY. PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS. INSTALLATION INSTRUCTIONS SUPPLIED WITH LAVATORY.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerance established by ANSI Standard A112.19.2
These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.
J16
© 2008 AS America Inc.