American Standard 1730 SERIES installation instructions Series Whirlpool/Bathing Pool, Thank You

483mm

(19)

COLONY™ CORNER

HIGH GLOSS ACRYLIC SHOWN LESS ALL FITTINGS

1730 SERIES

WHIRLPOOL/BATHING POOL

INSTALLATION INSTRUCTIONS

1064mm	1514mm
(41-7/8)	(59-5/8)
	ALT.
	PUMP

1546mm (60-7/8)

			PUMP
				PROVIDE ACCESS
318mm	686mm			FOR SERVICING
				PUMP & CONTROLS
(12-1/2)	(27)
		1168mm		ON/OFF
		(46)		SWITCH
	(6) JETS	C/L OF DRAIN		2 AIR
		OUTLET
				VALVES
		2134mm
		(84)		LEVELING
	TOP OF		83mm	STRINGER
51mm	DECK			NOT FOR
			(3-1/4)
(2)				SUPPORT
445mm				495mm
*(17-1/2)	70mm			(19-1/2)
				117mm
	(2-3/4)			(4-5/8)
	BATH SUPPORT MATERIAL		38mm (1-1/2)	ROUGH
				FLOOR
			O.D. TAILPIECE

THANK YOU...

for selecting an American Standard bath. Your new bath is shipped to you after careful inspection. The whirlpool version is completely assembled with pump, motor, and system piping. All you need to finish the installation are your selected fittings and electrical connections for a whirlpool.

To insure maximum performance and pleasure from this product, please follow the instructions and cautions.

List of Optional Components (not included):

• Apron Kit*

* see your American Standard Distributor

List of Required Components (not included):

•Drain 1583.470*

•Bath Filler*

* see your American Standard Distributor

*NOTE: If the optional apron (PN 0730.121) is to be used with this tub, the stringer height must be referenced from the finished floor.

GENERAL SPECIFICATIONS FOR 1730 WHIRLPOOL

INSTALLED SIZE		60 x 60 x 19-1/2 In.(1524 x 1524 x 495mm)
WEIGHT								115 Lbs. (52 Kg.)
WEIGHT w/WATER							908 Lbs. (412 Kg.)
GAL. TO OVERFLOW									95 Gal. (360 L.)
WHIRLPOOL MIN. OPERATING VOL.									65 Gal. (246 L.)
BATHING WELL AT SUMP					30 x 50 In. (762 x 1270mm)
BATHING WELL AT RIM			45-1/2 x 63-1/2 In.(1156 x 1613mm)
WATER DEPTH TO OVERFLOW									13 In. (330 mm)
FLOOR LOADING				36 Lbs./Sq. Ft. (177 Kgs/Sq. m.)
(PROJECTED AREA)
PTS.										27.8
CUBE (FT3)											54
	WHIRLPOOL ELECTRICAL SPECIFICATIONS
SYSTEM I PUMP						1.1 HP, 9.9 AMPS, 120V.

List of Required Tools and Supplies:

Tools		Supplies
•	Level	•	Nails
•	Tape Measure	•	Putty
•	Pipe Wrench	•	Caulking (waterproof)
•	Slip Joint Pliers	•	1 x 3 or 2 x 2
•	Screw Driver		Stringers
•	Standard	•	Drop Cloth
	Woodworking Tools	•	15 amp GFCI
•	Personal Safety		Outlet
	Equipment	•	Cement, Plaster,
•	Caulking Gun		Grout

GENERAL INSTALLATION INFORMATION

Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor immediately. After inspection and during installation, protect the bath from construction damage. After installation, and before enclosing with wallboard, tile, etc., water test the unit and check for leaks.

If a whirlpool, do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump, motor, or piping system.

Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and enclosing materials are provided by others. Check for availability of optional American Standard wall tiling bead (required for recess installations).

Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.

WARNING! Do not lift whirlpool by the piping harness at any time.

FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.

© American Standard Inc. 2003

753451-100 Rev. AAll product names listed herein are trademarks of American Standard Inc. unless otherwise noted.