American Standard 2064.4 installation instructions Bidet Faucet Installation, Spray Installation

	Installation
	Instructions
SERIN™	2064.400
Bidet Faucet and Transfer Valve with
Speed Connect™ Drain
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only on
American Standard faucets.	Certified to comply with ANSI A112.18.1
Speed Connect Drain*	M968924 Rev.1.3

•Fewer parts, installs in less time

•Never needs adjustment

•Guaranteed to seal properly the first time, every time.

*Your new American Standard faucet is designed to work only with the Speed Connect drain.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

Roughing-in			FINISHED	8 TO 12		Recommended tools
Dimensions	TRANSFER VALVE
			WALL
	(FOR FLUSHING
BIDET OUTLINE	RIM OR SPRAY)				2-1/4
			(C)	(H)
IS SYMBOLIC	7/8 DIA.					Screwdriver	Plumbers' Putty or
					DIA.
			1-3/16				Caulking
DOUCHE ADJ. 1-1/4
		2-1/8	DIA.		4-1/4
SPRAY	TO 2-1/4	DIA.	1-1/4
						Phillips Screwdriver
	1-3/8		MAX.				Channel Locks
3-7/8					FOR GROUND JOINT
	DIA.				CONNECTION OR 1/2 "
					O.D. SLIP (INLETS)
			FINISHED		REAR VIEW WITH
	5-1/2		FLOOR		WALL REMOVED	Adjustable Wrench
			1-1/4 O.D. TAILPIECE				Tubing Cutter

1			Turn off hot and cold water
	BIDET FAUCET INSTALLATION	CAUTION
			supplies before beginning.	6

Place RUBBER RING (10) into ESCUTCHEON (4).

Install LOCKNUT (1) and RUBBER WASHER (2) onto VALVE BODIES (3, 3a). From under side of mounting surface, install VALVE BODY (3, 3a) through valve mounting holes. Threads of VALVE BODY (3, 3a) should extent at least 5/16 of a inch above mounting surface top. Fig. A. Thread ESCUTCHEON (4) onto VALVE BODIES

(3, 3a) until snug against internal stop. If necessary, adjust LOCKNUT (1).

	7
4	BIDET
10	LEDGE
	8

Tighten LOCKNUTS (1) with WRENCH (5) (supplied) to secure VALVE BODIES (3, 3a).

Remove ESCUTCHEON (6), WASHER (7) and UPPER GASKET (8) from TRANSFER VALVE (9). Insert TRANSFER VALVE (9) into the center forward hole of BIDET.

Fig. A.	4
	10
5/16''
	MOUNTING
MIN.
	SURFACE
	2

		3		3a
2
	HOT		9	COLD
1

Replace UPPER GASKET (8) and WASHER (7) and ESCUTCHEON (6) until it locks against internal stop. Position the side threaded outlet rearward and secure MOUNTING NUT (11).

1

3, 3a

5

11

2 SPRAY INSTALLATION

Assemble SPRAY BODY (1) to BIDET. Using putty, seal underside	6
of SPRAY BODY FLANGE (2) and secure with NUT (3).

Thread SPRAY HOSE (4) with SEAL WASHER (5) to SPRAY BODY (1). Connect other end of HOSE (4) with SEAL WASHER (6) to side outlet NIPPLE (7) of the TRANSFER VALVE (8).

Thread SPRAY CAP (9) onto SPRAY BODY (1).

8	2	9
	PUTTY	1

7

3

45

4