American Standard installation instructions 2071S, Monoblock, Lavatory Faucet

Installation Instructions

T H E	MONOBLOCK	2071
	LAVATORY FAUCET
C O L L E C T I O N™		2071S
by	WITH CROSS HANDLE

Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.

To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.

Certified to comply with ANSI A112.18.1M

M 9 6 8 2 9 0 A

TOOLS REQUIRED

Channel Locks Adjustable Wrench Plumbers' Putty or Caulking Phillips Screwdriver

CARE INSTRUCTIONS:

To keep your new faucet looking new, please follow these simple care instructions:

DO: Simply rinse the faucet clean with clear water. Dry the faucet with a soft cotton cloth.

DO NOT:

Do not use any abrasive cleaners, cloths, or paper towels.

Do not use any cleaning agents containing acids, polish abrasives, or harsh cleaners or soaps.

Regular and routine cleaning will reduce the need for heavy cleaning and polishing. If heavy cleaning is

1
	INSTALL FAUCET	CAUTION	Turn off water at
			main supply.

Remove as much surface dirt and film using clear water and soft cotton cloth (as described above).

Use any of the following to remove tough surface film and build-up:

Mild liquid detergents

Clear ammonia free liquid glass cleaners

Non-acidic, non-abrasive gentle liquid or fully dissolved powder cleansers mixed according to manufacturers directions.

Non-abrasive liquid polishers

Once clean, rinse faucet again with clear water to thoroughly remove cleaner or polish and blot dry with a soft cotton cloth.

Failure to follow these care instructions may damage the Faucet's finish.

INSTALLATION OPTIONS; Faucet may be installed with ESCUTCHEON PLATE (1) or for center hole only with ESCUTCHEON RING (2).

INSTALLATION with ESCUTCHEON PLATE (1)

No sealant is required unless mounting surface is uneven for 3-hole	7
(4" centers) installation with ESCUTCHEON PLATE (1). Place ESCUTCHEON
PLATE (1) over mounting holes on lavatory sink or mounting surface.

Feed FLEXIBLE FAUCET HOSES (3) and MOUNTING STUD (4) through hole in ESCUTCHEON PLATE (1). Seat ESCUTCHEON PLATE (1) boss into groove in Faucet base.

From below, install MOUNTING GASKET with RETAINING WASHER (5) and Nut (6) onto

STUD (4). Pull Faucet to front of sink, so STUD BOSS

(4) rests against sink hole. Before final tightening, align Faucet and ESCUTCHEON (1) so they are centered on mounting surface. Tighten NUT (6) to secure Faucet

GROOVE IN

Insert LIFT ROD (7).ESCUTCHEON RING BASE

GROOVE IN

FAUCET BASE

BOSS

2

INSTALLATION with ESCUTCHEON RING (2)

For single hole installation use ESCUTCHEON RING (2). Install SEAL WASHER (6) into groove in ESCUTCHEON RING (2) base and place over over mounting hole in lavatory sink or mounting surface.

Feed FLEXIBLE FAUCET HOSES (3) and MOUNTING STUD (4) through hole in ESCUTCHEON RING (2). Seat ESCUTCHEON RING (2) boss into groove in Faucet base.

From below, install MOUNTING GASKET with RETAINING WASHER (5) and Nut (6) onto STUD (4). Pull Faucet to front of sink, so STUD

(4)rests against sink hole. Before final tightening, align Faucet and ESCUTCHEON (1) so they are centered on mounting surface. Tighten NUT (6) to secure Faucet

Insert LIFT ROD (7).

6

LAVATORY SINK

OR MOUNTING

SURFACE

3

1

4

5

6