9b | 10 | TOP | ARM | NIPPLE |
|
|
|
| REFILL |
|
|
|
| TUBE |
|
|
|
| TANK |
|
|
|
| LEVER |
|
| CRITICAL LEVEL |
|
|
|
| MARK ("C.L.") |
|
|
|
| MUST BE |
|
|
|
| 1" ABOVE |
|
|
|
| OVERFLOW PIPE | FLOAT | Fig. 10A |
|
|
| ||
|
|
| CUP | |
|
| FILL |
|
|
|
| VALVE |
|
|
| WATER LEVEL | |
VALVE | ADJUSTMENT | |
ROD | ||
BODY |
| |
| ADJUSTABLE | |
SHANK | HEIGHT | |
WASHER |
| |
LOCK NUT | THREADED | |
| SHANK | |
CONE WASHER |
| |
| PARTS FOR WATER | |
COUPLING NUT | CONNECTION | |
(SEE STEP 9) | ||
(HAND TIGHT ONLY) | ||
Diagram 1 | ||
|
|
|
|
|
|
| With correct washers in | ADJUSTMENTS | ||||||
|
|
|
|
|
| place (see Step 9a), | a. Adjust water level. Water level should be adjusted to level indicated in | ||||||
|
|
|
|
|
| tighten COUPLING NUT | tank by adjusting float cup. See Step 11 for water level adjustment method. | ||||||
|
|
|
|
|
| 1/4 turn beyond hand tight. | IMPORTANT: | ||||||
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
| DO NOT OVERTIGHTEN. | b. If bowl fails to siphon, an adjustment may be required with the lift chain. | ||||||
|
|
|
|
|
| Simply remove the bead chain from the retainment clip (see Fig. 10A) | |||||||
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
| and take up slack on the chain, and reinsert on lift rod. Make sure the chain | ||
|
|
|
|
|
|
|
|
|
|
| is not too taught. | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
11 |
|
|
|
|
|
|
|
|
| Turn on water supply. | 12 |
| CARE AND CLEANING |
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| Submerge the FLOAT |
|
| When cleaning your toilet, wash it with mild, soapy water, rinse |
|
|
|
|
|
|
|
|
|
| CUP under the water for |
|
| |
|
|
|
|
|
|
|
|
|
|
|
| thoroughly with clear water and dry with a soft cloth. | |
|
|
|
|
|
|
|
|
|
| 30 seconds. Adjust the |
|
| |
|
|
|
|
|
|
|
|
|
|
|
| WARNING: Do not use | |
|
|
|
|
|
|
|
|
|
| water to desired level by | ! |
| |
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| turning WATER LEVEL |
|
| can seriously damage fittings in the tank. This damage can |
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| ADJUSTMENT ROD |
|
| cause leakage and property damage. |
|
|
|
|
|
|
|
|
|
| and moving FLOAT |
|
|
|
|
|
|
|
|
|
|
|
|
| CUP up or down. |
|
| American Standard shall not be responsible or liable for |
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
| any damage caused by the use of |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
13 TROUBLE SHOOTING FLUSH VALVE | 13a | REFILL TUBE REPLACEMENT : | |||||||||||
SEAL REPLACEMENT:
1.Turn off water supply and flush toilet to empty tank.
2.Disconnect chain from trip lever by removing hair pin cotter
| and clevis pin. |
|
|
3. | Parially lift and support piston bottom with one hand. | Locate bottom portion of | |
4. | Remove thumbscrew by turning | hose clip to vent tube at | |
5. | Remove piston top and gasket. | location as shown. | |
6. | Replace gasket with new gasket. |
| |
7. Reverse procedure, turn thumbscrew until 2 clicks are felt. |
| ||
HAIR PIN | THUMBSCREW |
| |
COTTER |
|
| |
|
| PISTON TOP |
|
|
| GASKET |
|
|
| PISTON BOTTOM |
|
NOTE: DO NOT ADD ANY FOREIGN MATERIALS TO THE SEALING SURFACE.
- 4 - |
