Installation Instructions
| MONOBLOCK | 2171 |
| T H E | |
C O L L E C T I O N™LAVATORY FAUCET |
| |
by | SINGLE LEVER |
|
Thank you for selecting
To ensure that your installation proceeds
Certified to comply with ANSI A112.18.1M
M 9 6 8 2 9 1 C
TOOLS REQUIRED
Channel Locks | Adjustable Wrench | Plumbers' Putty or Caulking | Phillips Screwdriver |
To keep your new faucet looking new, please follow these simple care instructions:
DO: Simply rinse the faucet clean with clear water. Dry the faucet with a soft cotton cloth.
DO NOT:
Do not use any abrasive cleaners, cloths, or paper towels.
Do not use any cleaning agents containing acids, polish abrasives, or harsh cleaners or soaps.
Regular and routine cleaning will reduce the need for heavy cleaning and polishing. If heavy cleaning is required, the following procedures are recommended:
Remove as much surface dirt and film using clear water and soft cotton cloth (as described above).
Use any of the following to remove tough surface film and
Mild liquid detergents
Clear ammonia free liquid glass cleaners
Once clean, rinse faucet again with clear water to thoroughly remove cleaner or polish and blot dry with a soft cotton cloth.
Failure to follow these care instructions may damage the Faucet's finish.
1 |
|
|
|
|
|
|
|
|
|
|
| ||
INSTALL FAUCET |
| CAUTION | Turn off water at |
|
|
|
|
|
| ||||
| main supply. |
|
|
|
|
|
| ||||||
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
| |||
|
|
| INSTALLATION OPTIONS; Faucet may be installed with ESCUTCHEON |
|
|
| |||||||
|
|
| PLATE (1) or for center hole only with ESCUTCHEON RING (2). |
|
|
| |||||||
|
|
| INSTALLATION with ESCUTCHEON PLATE (1) |
|
|
|
| 7 | |||||
|
|
|
|
|
|
|
|
|
| ||||
|
|
| No sealant is required unless mounting surface is uneven for | ||||||||||
|
|
| |||||||||||
|
|
| installation with ESCUTCHEON PLATE (1). Place ESCUTCHEON PLATE (1) over | ||||||||||
|
|
| mounting holes on lavatory sink or mounting surface. |
|
|
| |||||||
|
|
| Feed FLEXIBLE FAUCET HOSES (3) and MOUNTING STUD (4) through |
|
|
| |||||||
|
|
|
|
|
| ||||||||
|
|
| hole in ESCUTCHEON PLATE (1). Seat ESCUTCHEON PLATE (1) boss |
|
|
| |||||||
|
|
| into groove in Faucet base. |
|
|
|
|
|
| GROOVE IN | |||
|
|
| From below, install MOUNTING GASKET with |
|
|
|
| FAUCET BASE | |||||
|
|
|
|
|
|
|
| BOSS | |||||
|
|
|
|
|
|
|
| ||||||
|
|
| RETAINING WASHER (5) and Nut (6) onto |
|
|
|
|
| |||||
|
|
| BOSS |
|
|
|
| ||||||
|
|
| STUD (4). Pull Faucet to front of sink, so STUD |
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
| ||||
|
|
| (4) rests against sink hole. Before final tightening, |
|
|
|
|
|
|
| |||
|
|
| align Faucet and ESCUTCHEON (1) so they are |
|
|
|
|
|
|
| |||
|
|
| centered on mounting surface. Tighten NUT (6) |
|
|
|
|
|
| 2 | |||
|
|
| to secure Faucet |
| GROOVE IN |
|
| ||||||
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
| |||||
|
|
| Insert LIFT ROD (7). |
| ESCUTCHEON |
|
|
| |||||
|
|
|
|
|
|
| |||||||
|
|
|
| RING BASE |
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
INSTALLATION with ESCUTCHEON RING (2) | 6 | |
For single hole installation use ESCUTCHEON |
| |
RING (2). Install SEAL WASHER (6) into groove |
| |
in ESCUTCHEON RING (2) base and place over | LAVATORY SINK | |
over mounting hole in lavatory sink or mounting | ||
OR MOUNTING | ||
surface. | SURFACE |
Feed FLEXIBLE FAUCET HOSES (3) and MOUNTING
STUD (4) through hole in ESCUTCHEON RING (2).3
Seat ESCUTCHEON RING (2) boss into groove in
Faucet base.
From below, install MOUNTING GASKET with
RETAINING WASHER (5) and Nut (6) onto
STUD (4). Pull Faucet to front of sink, so STUD
(4)rests against sink hole. Before final tightening, align Faucet and ESCUTCHEON (1) so they are centered on mounting surface. Tighten NUT (6) to secure Faucet
Insert LIFT ROD (7).
1
4
5
6