INSTALLATION INSTRUCTIONS
CARE AND MAINTENANCE
Colony FitRight Two-Piece Toilet
Models 2435 / 2436 / 2437 / 2453 / 2485 / 2486 / 2487 / 3510
Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.
!CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
NOTE: Pictures may not exactly define contour of china and components.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife | Regular Screwdriver | Adjustable Wrench | Sealant | Tape Measure |
Hacksaw | Wax Ring/Gasket | Flexible Supply Tube | Closet Bolts | Carpenters Level |
1REMOVE OLD TOILET
a.Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b.Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c.Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d.Remove closet bolts from flange and clean away old wax, putty, etc. from base area. NOTE: Mounting surface must be clean and level before new toilet is installed!
2 |
|
|
|
| 3 |
| |
MODELS | DIMENSION “A” |
|
| ||||
| NOTE: Distance from wall to closet |
|
|
|
|
|
|
| 2485 | 2487 | 10" |
|
|
| |
| flange centerline must be as listed: |
|
|
| |||
| 2486 |
| (254mm) |
|
| CLOSET FLANGE | |
|
|
|
|
| |||
|
| 2435 | 2453 | 12" |
|
|
|
|
| 2436 | 3510 |
|
|
| |
|
| (305mm) |
|
|
| ||
|
| 2437 |
|
|
|
| |
| FINISHED WALL |
|
|
|
|
| |
|
|
|
|
|
| A | |
|
|
|
|
|
|
| |
|
| CLOSET BOLTS | |
|
| SUPPLY | |
|
| AS | |
|
| REQ'D. | |
|
| INSTALL CLOSET BOLTS | |
A | FINISHED | Install closet bolts in flange channel and slide | |
FLOOR | into place parallel to wall. | ||
| |||
4 |
| 5 | |
SEALANT |
| WAX RING | |
| NUT | ||
|
| ||
|
| TAPERED | |
|
| WASHER | |
|
| CLOSET | |
|
| BOLT | |
|
| FLANGE |
INSTALL WAX SEAL | POSITION TOILET ON FLANGE | |
Invert toilet on floor (cushion to prevent damage), and | ||
a. Unplug floor waste opening and install toilet on closet flange so bolts project | ||
install wax ring evenly around waste flange (horn), with | ||
through mounting holes. | ||
tapered end of ring facing toilet. Apply a thin bead of | ||
b. Loosely install retainer washers and nuts. Side of washers marked "THIS | ||
sealant around toilet base. | ||
SIDE UP" must face up! | ||
|
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a I n c . | |
© A S A m e r i c a I n c . 2 0 0 8 |
S A V E F O R F U T U R E U S E
