American Standard 2711E installation instructions General Installation Information

ELLISSE ELITE™ 6' X 48"

HIGH GLOSS ACRYLIC SHOWN LESS ALL FITTINGS

2711E SERIES WHIRLPOOL

INSTALLATION INSTRUCTIONS

305mm

(12)

1219mm

(48)

	1829mm
	(72)
	ON/OFF SWITCH
927mm	OUTLINE OF CUTOUT
(36-1/2)		102mm
	1791 X 1181
		(4)
	(70-1/2 X 46-1/2)
		C/L OF
		DRAIN
	229mm x 356mm
	(9 x 14) FLOOR	PUMP
	CUTOUT

THANK YOU...

for selecting an American Standard bath. Your new bath is shipped to you after careful inspection. The whirlpool version is completely assembled with pump, motor, and system piping. All you need to finish the installation are your selected fittings and electrical connections for a whirlpool.

To insure maximum performance and pleasure from this product, please follow the instructions and cautions.

List of Optional Components (not included):

RECOMMENDED FITTING LOCATION 64X279mm 2-1/2 X 11)

51mm

(2)

INTEGRAL

FEET

SUPPORT

GRAB BAR

FITTING AREA	OPTIONAL	PROVIDE ACCESS
		TO PUMP FOR SERVICE
	DECK FITTING
		ON ALL INSTALLATIONS
	AREA

	IN-LINE	LEVELING STRINGER
	HEATER	(NOT FOR SUPPORT)
	REMOVABLE		C/L OF
	BLANK
			OVERFLOW
		105mm	546mm
			(21-1/2)
		(4-1/8)
		ROUGH	495mm
		FLOOR	(19-1/2)
1-1/2 N.P.T.M. THREADS
1-1/2 O.D.TAILPIECE	64mm		121mm
			(4-3/4)
	(2-1/2)

•Flex-Jet Pulse Jet Kit*

•Flex-Jet Soft Jet Kit*

•E-Z-Install Heater*

•Tile Bead Kit*

List of Required Components (not included):

• Drain*• Bath Filler*

* see your Home Depot Retailer

List of Required Tools and Supplies:

GENERAL SPECIFICATIONS FOR 2711E WHIRLPOOL

INSTALLED SIZE		72 x 48 x 21-1/2 In. (1829 x 1219 x 546mm)
WEIGHT				148 Lbs. (67 Kg.)
WEIGHT w/WATER				965 Lbs. (434 Kg.)
GAL. TO OVERFLOW				95 Gal. (360 L)
WHIRLPOOL MIN. OPERATING VOL.				74 Gal. (280 L)
BATHING WELL AT SUMP				43 x 28 In. (1092 x 711mm)
BATHING WELL AT RIM				68 x 38 In. (1727 x 965mm)
WATER DEPTH TO OVERFLOW				14-5/8 In. (371mm)
FLOOR LOADING			40 Lbs./Sq.Ft. (195 Kgs./Sq.m)
(PROJECTED AREA)
PTS.					41.7
CUBE (FT3)						81.9
	WHIRLPOOL ELECTRICAL SPECIFICATIONS
PUMP				2.1 HP, 14.4 AMPS ,120V.

GENERAL INSTALLATION INFORMATION

Tools		Supplies
•	Level	•	Nails
•	Tape Measure	•	Putty
•	Pipe Wrench	•	Caulking (waterproof)
•	Slip Joint Pliers	•	1 x 3 or 2 x 2
•	Screw Driver		Stringers
•	Standard	•	Drop Cloth
	Woodworking Tools	•	20 amp GFI
•	Personal Safety		Outlet
	Equipment	•	Cement, Plaster,
•	Caulking Gun		Grout

Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor immediately.

After inspection and during installation, protect the bath from construction damage. After installation, and before enclosing with wallboard, tile, etc., water test the unit and check for leaks.

Do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump, motor, or piping system.

Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and enclosing materials are provided by others. Check for availability of optional American Standard wall tiling bead (required for recess installations).

Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.

WARNING! Do not lift whirlpool by the piping harness at any time.

FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.

© American Standard Inc. 2003

752873-100 REV. BAll product names listed herein are trademarks of American Standard Inc. unless otherwise noted.