Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna manual Rider 11 C, Rider 13 C, Rider 16 AWD, Rider 16 C, Operator′s manual, English

Models: 11 C 16 C 16 AWD 13 C

1 40

Page 1

Operator′s manual

Rider 11 C	Rider 13 C
Rider 16 AWD	Rider 16 C

Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.

English

Page 1

Image 1

Husqvarna manual Rider 11 C, Rider 13 C, Rider 16 AWD, Rider 16 C, Operator′s manual, English

Contents

Rider 13 C Rider 11 CRider 16 AWD Rider 16 CContents CONTENTSCONTENTS Service journalDear Customer INTRODUCTIONDriving and transport on public roads TowingSerial Number Good serviceINTRODUCTION Pre-delivery service Service journalAfter the ﬁrst 5 hours Symbols KEY TO SYMBOLSDrive very slowly if no cutting unit is ﬁtted Starting instructions KEY TO SYMBOLSCheck the engine’s oil level Check the hydrostat’s oil level Lift up the cutting unit Apply and lock the parking brakeSafety instructions SAFETY INSTRUCTIONSInsure your Rider General useThis is what you do Driving on slopesWARNING! You must use approved personal IMPORTANT INFORMATIONWARNING! The battery contains lead and MaintenanceChildren WARNING! The engine and the exhaustSAFETY INSTRUCTIONS TransportIMPORTANT INFORMATION Location of the controls WHAT IS WHAT?Presentation PRESENTATIONClutch pedal, Rider 11 C Brake pedal / Parking brakeExercise care and refuel outdoors see safety instructions Cutting height adjustment leverCutting unit Lifting lever for the cutting unitRelease lever Rider 16 AWD Release lever Rider 13 C, Rider 16 CClutch control, rear axle Clutch control, front axleBefore starting DrivingStart the engine IMPORTANT INFORMATIONConnecting the jump leads Starting the engine with a weak batteryRemove the cables in the reverse order WARNING! Never run the engine indoors, inCutting tips Driving the Rider2 For Rider 13 C, Rider 16 AWD and Rider 16 C 3 For Rider 11 CStop the engine Starting on a slope, manual gearbox, Rider 11 CWARNING! Do not use the machine on DrivingMaintenance schedule MaintenanceMaintenance interval The engine is switched off The ignition key is removedChecking and adjusting the steering wires CleaningRemoving of the machine hoods Engine coverAdjusting the parking brake Rider 13 C, Rider 16 C Adjusting the brake Rider 11 CWARNING! A poorly adjusted brake can Checking the brake Rider 11 CAdjusting the throttle wire Adjusting the parking brake Rider 16 AWDWARNING! A poorly adjusted parking brake Replacing the air ﬁlterChecking the fuel pump’s air ﬁlter Replacement of fuel ﬁlterChecking the tyre pressure MaintenanceWARNING! Procedures on contact with acid Check the level of the battery acidIgnition system FusesMaintenance Check the safety systemRider 13 C, Rider 16 C Rider 16 AWD MaintenanceEnglish Checking and adjustment of the cutting unit’s ground pressure Adjusting the parallelism of the cutting unitwhen the engine is running. Mind your ﬁngers Checking the engine’s cooling air intakePlacing in the service position Service position for the cutting unitMaintenance Checking the blades Restoring from service positionRemoving the BioClip plug WARNING! If the blades are crackedChecking the engine’s oil level LubricationReplacing the engine oil WARNING! Engine oil can be very hot if it isLubrication Rider 11 C Lubricating the belt adjusterGeneral lubrication Rider 16 AWDProblem Troubleshooting scheduleProcedure Storage ServiceWinter storage GuardDimensions TECHNICAL DATARider 11 C EngineTECHNICAL DATA Rider 13 CDimensions Rider 16 AWDElectrical system Rider 16 CTECHNICAL DATA DimensionsEC-declaration of conformity Applies to Europe only ´z+S!¶6¶¨ 38 - English ´z+S!¶6¶¨TECHNICAL DATA Page 1151019-26 ´z+S!¶6¶¨ ´z+S!¶6¶¨