Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna 11 C Release lever Rider 13 C, Rider 16 C, Release lever Rider 16 AWD, Presentation

Models: 11 C 16 C 16 AWD 13 C

1 40

Download 40 pages 23.12 Kb

Page 15

Release lever Rider 13 C, Rider 16 C

PRESENTATION

Release lever Rider 13 C, Rider 16 C

The release control must be pulled out in order for the machine to be moved when the engine is shutoff. Pull the controls to the end positions, do not use an intermediate position.

•Pull out the control to disengage the drive system.

•Push in the control to engage to the drive system.

Release lever Rider 16 AWD

Rider 16 AWD has one control for the front axle and one control for the rear axle.

Should you attempt to drive the machine with the clutch controls pulled out it will not move. The drive on the axle is disengaged when one of the controls is pulled out.

IMPORTANT!

Always drive the machine with both clutch controls pressed in.

Clutch control, rear axle

•Control drawn out, drive system disengaged.

•Control depressed, drive system engaged.

Clutch control, front axle

The control is positioned on the inside of the left front wheel.

•Rear control (pulled out), drive system disengaged.

•Front control (pushed in), drive system engaged.

English – 15

Image 15

Husqvarna 11 C Release lever Rider 13 C, Rider 16 C, Release lever Rider 16 AWD, Clutch control, rear axle, Presentation

Contents

Rider 16 C Rider 11 CRider 13 C Rider 16 AWDService journal CONTENTSContents CONTENTSTowing INTRODUCTIONDear Customer Driving and transport on public roadsGood service Serial NumberINTRODUCTION Service journal Pre-delivery serviceAfter the ﬁrst 5 hours Symbols KEY TO SYMBOLSLift up the cutting unit Apply and lock the parking brake KEY TO SYMBOLSDrive very slowly if no cutting unit is ﬁtted Starting instructions Check the engine’s oil level Check the hydrostat’s oil levelGeneral use SAFETY INSTRUCTIONSSafety instructions Insure your RiderIMPORTANT INFORMATION Driving on slopesThis is what you do WARNING! You must use approved personalWARNING! The engine and the exhaust MaintenanceWARNING! The battery contains lead and ChildrenTransport SAFETY INSTRUCTIONSIMPORTANT INFORMATION Location of the controls WHAT IS WHAT?Brake pedal / Parking brake PRESENTATIONPresentation Clutch pedal, Rider 11 CLifting lever for the cutting unit Cutting height adjustment leverExercise care and refuel outdoors see safety instructions Cutting unitClutch control, front axle Release lever Rider 13 C, Rider 16 CRelease lever Rider 16 AWD Clutch control, rear axleIMPORTANT INFORMATION DrivingBefore starting Start the engineWARNING! Never run the engine indoors, in Starting the engine with a weak batteryConnecting the jump leads Remove the cables in the reverse order3 For Rider 11 C Driving the RiderCutting tips 2 For Rider 13 C, Rider 16 AWD and Rider 16 CDriving Starting on a slope, manual gearbox, Rider 11 CStop the engine WARNING! Do not use the machine onThe engine is switched off The ignition key is removed MaintenanceMaintenance schedule Maintenance intervalEngine cover CleaningChecking and adjusting the steering wires Removing of the machine hoodsChecking the brake Rider 11 C Adjusting the brake Rider 11 CAdjusting the parking brake Rider 13 C, Rider 16 C WARNING! A poorly adjusted brake canReplacing the air ﬁlter Adjusting the parking brake Rider 16 AWDAdjusting the throttle wire WARNING! A poorly adjusted parking brakeMaintenance Replacement of fuel ﬁlterChecking the fuel pump’s air ﬁlter Checking the tyre pressureFuses Check the level of the battery acidWARNING! Procedures on contact with acid Ignition systemMaintenance Check the safety systemMaintenance Rider 13 C, Rider 16 C Rider 16 AWDEnglish Checking the engine’s cooling air intake Adjusting the parallelism of the cutting unitChecking and adjustment of the cutting unit’s ground pressure when the engine is running. Mind your ﬁngersService position for the cutting unit Placing in the service positionMaintenance WARNING! If the blades are cracked Restoring from service positionChecking the blades Removing the BioClip plugWARNING! Engine oil can be very hot if it is LubricationChecking the engine’s oil level Replacing the engine oilRider 16 AWD Lubricating the belt adjusterLubrication Rider 11 C General lubricationTroubleshooting schedule ProblemProcedure Guard ServiceStorage Winter storageEngine TECHNICAL DATADimensions Rider 11 CRider 16 AWD Rider 13 CTECHNICAL DATA DimensionsDimensions Rider 16 CElectrical system TECHNICAL DATA´z+S!¶6¶¨ 38 - English ´z+S!¶6¶¨ EC-declaration of conformity Applies to Europe onlyTECHNICAL DATA Page 1151019-26 ´z+S!¶6¶¨ ´z+S!¶6¶¨