Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna 13 C, 16 AWD, 16 C, 11 C manual ´z+S!¶6¶¨ ´z+S!¶6¶¨, 1151019-26

Models: 11 C 16 C 16 AWD 13 C

1 40

Download 40 pages 23.12 Kb

Page 40

Image 40

1151019-26

´®z+S!¶6¶¨ ´®z+S!¶6¶¨ 2007-12-14

Page 40

Image 40

Husqvarna 13 C, 16 AWD, 16 C, 11 C manual ´z+S!¶6¶¨ ´z+S!¶6¶¨, 1151019-26

Contents

Rider 11 C Rider 13 CRider 16 AWD Rider 16 CCONTENTS ContentsCONTENTS Service journalINTRODUCTION Dear CustomerDriving and transport on public roads TowingSerial Number Good serviceINTRODUCTION Pre-delivery service Service journalAfter the ﬁrst 5 hours KEY TO SYMBOLS SymbolsKEY TO SYMBOLS Drive very slowly if no cutting unit is ﬁtted Starting instructionsCheck the engine’s oil level Check the hydrostat’s oil level Lift up the cutting unit Apply and lock the parking brakeSAFETY INSTRUCTIONS Safety instructionsInsure your Rider General useDriving on slopes This is what you doWARNING! You must use approved personal IMPORTANT INFORMATIONMaintenance WARNING! The battery contains lead andChildren WARNING! The engine and the exhaustSAFETY INSTRUCTIONS TransportIMPORTANT INFORMATION WHAT IS WHAT? Location of the controlsPRESENTATION PresentationClutch pedal, Rider 11 C Brake pedal / Parking brakeCutting height adjustment lever Exercise care and refuel outdoors see safety instructionsCutting unit Lifting lever for the cutting unitRelease lever Rider 13 C, Rider 16 C Release lever Rider 16 AWDClutch control, rear axle Clutch control, front axleDriving Before startingStart the engine IMPORTANT INFORMATIONStarting the engine with a weak battery Connecting the jump leadsRemove the cables in the reverse order WARNING! Never run the engine indoors, inDriving the Rider Cutting tips2 For Rider 13 C, Rider 16 AWD and Rider 16 C 3 For Rider 11 CStarting on a slope, manual gearbox, Rider 11 C Stop the engineWARNING! Do not use the machine on DrivingMaintenance Maintenance scheduleMaintenance interval The engine is switched off The ignition key is removedCleaning Checking and adjusting the steering wiresRemoving of the machine hoods Engine coverAdjusting the brake Rider 11 C Adjusting the parking brake Rider 13 C, Rider 16 CWARNING! A poorly adjusted brake can Checking the brake Rider 11 CAdjusting the parking brake Rider 16 AWD Adjusting the throttle wireWARNING! A poorly adjusted parking brake Replacing the air ﬁlterReplacement of fuel ﬁlter Checking the fuel pump’s air ﬁlterChecking the tyre pressure MaintenanceCheck the level of the battery acid WARNING! Procedures on contact with acidIgnition system FusesCheck the safety system MaintenanceRider 13 C, Rider 16 C Rider 16 AWD MaintenanceEnglish Adjusting the parallelism of the cutting unit Checking and adjustment of the cutting unit’s ground pressurewhen the engine is running. Mind your ﬁngers Checking the engine’s cooling air intakePlacing in the service position Service position for the cutting unitMaintenance Restoring from service position Checking the bladesRemoving the BioClip plug WARNING! If the blades are crackedLubrication Checking the engine’s oil levelReplacing the engine oil WARNING! Engine oil can be very hot if it isLubricating the belt adjuster Lubrication Rider 11 CGeneral lubrication Rider 16 AWDProblem Troubleshooting scheduleProcedure Service StorageWinter storage GuardTECHNICAL DATA DimensionsRider 11 C EngineRider 13 C TECHNICAL DATADimensions Rider 16 AWDRider 16 C Electrical systemTECHNICAL DATA DimensionsEC-declaration of conformity Applies to Europe only ´z+S!¶6¶¨ 38 - English ´z+S!¶6¶¨TECHNICAL DATA Page ´z+S!¶6¶¨ ´z+S!¶6¶¨ 1151019-26