Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna 11 C, 13 C Key To Symbols, Check the engine’s oil level Check the hydrostat’s oil level

Models: 11 C 16 C 16 AWD 13 C

1 40

Download 40 pages 23.12 Kb

Page 7

Image 7

KEY TO SYMBOLS

Drive very slowly if no cutting unit is ﬁtted

Starting instructions

Check the engine’s oil level

Check the hydrostat’s oil level

Lift up the cutting unit

Apply and lock the parking brake.

If the engine is cold, use the choke

Release the parking brake before driving

Switch off the engine and take off the ignition cable before repairs or maintenance

English – 7

Page 7

Image 7

Husqvarna 11 C, 13 C, 16 AWD Key To Symbols, Drive very slowly if no cutting unit is ﬁtted Starting instructions, English

Contents

Rider 16 C Rider 11 CRider 13 C Rider 16 AWDService journal CONTENTSContents CONTENTSTowing INTRODUCTIONDear Customer Driving and transport on public roadsSerial Number Good serviceINTRODUCTION Pre-delivery service Service journalAfter the ﬁrst 5 hours Symbols KEY TO SYMBOLSLift up the cutting unit Apply and lock the parking brake KEY TO SYMBOLSDrive very slowly if no cutting unit is ﬁtted Starting instructions Check the engine’s oil level Check the hydrostat’s oil levelGeneral use SAFETY INSTRUCTIONSSafety instructions Insure your RiderIMPORTANT INFORMATION Driving on slopesThis is what you do WARNING! You must use approved personalWARNING! The engine and the exhaust MaintenanceWARNING! The battery contains lead and ChildrenSAFETY INSTRUCTIONS TransportIMPORTANT INFORMATION Location of the controls WHAT IS WHAT?Brake pedal / Parking brake PRESENTATIONPresentation Clutch pedal, Rider 11 CLifting lever for the cutting unit Cutting height adjustment leverExercise care and refuel outdoors see safety instructions Cutting unitClutch control, front axle Release lever Rider 13 C, Rider 16 CRelease lever Rider 16 AWD Clutch control, rear axleIMPORTANT INFORMATION DrivingBefore starting Start the engineWARNING! Never run the engine indoors, in Starting the engine with a weak batteryConnecting the jump leads Remove the cables in the reverse order3 For Rider 11 C Driving the RiderCutting tips 2 For Rider 13 C, Rider 16 AWD and Rider 16 CDriving Starting on a slope, manual gearbox, Rider 11 CStop the engine WARNING! Do not use the machine onThe engine is switched off The ignition key is removed MaintenanceMaintenance schedule Maintenance intervalEngine cover CleaningChecking and adjusting the steering wires Removing of the machine hoodsChecking the brake Rider 11 C Adjusting the brake Rider 11 CAdjusting the parking brake Rider 13 C, Rider 16 C WARNING! A poorly adjusted brake canReplacing the air ﬁlter Adjusting the parking brake Rider 16 AWDAdjusting the throttle wire WARNING! A poorly adjusted parking brakeMaintenance Replacement of fuel ﬁlterChecking the fuel pump’s air ﬁlter Checking the tyre pressureFuses Check the level of the battery acidWARNING! Procedures on contact with acid Ignition systemMaintenance Check the safety systemRider 13 C, Rider 16 C Rider 16 AWD MaintenanceEnglish Checking the engine’s cooling air intake Adjusting the parallelism of the cutting unitChecking and adjustment of the cutting unit’s ground pressure when the engine is running. Mind your ﬁngersPlacing in the service position Service position for the cutting unitMaintenance WARNING! If the blades are cracked Restoring from service positionChecking the blades Removing the BioClip plugWARNING! Engine oil can be very hot if it is LubricationChecking the engine’s oil level Replacing the engine oilRider 16 AWD Lubricating the belt adjusterLubrication Rider 11 C General lubricationProblem Troubleshooting scheduleProcedure Guard ServiceStorage Winter storageEngine TECHNICAL DATADimensions Rider 11 CRider 16 AWD Rider 13 CTECHNICAL DATA DimensionsDimensions Rider 16 CElectrical system TECHNICAL DATAEC-declaration of conformity Applies to Europe only ´z+S!¶6¶¨ 38 - English ´z+S!¶6¶¨TECHNICAL DATA Page 1151019-26 ´z+S!¶6¶¨ ´z+S!¶6¶¨