Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna 16 AWD, 13 C, 16 C, 11 C Service journal, Pre-delivery service, After the ﬁrst 5 hours

Models: 11 C 16 C 16 AWD 13 C

1 40

Download 40 pages 23.12 Kb

Page 5

Service journal

Service journal

Pre-delivery service

1 Top up battery with acid and charge for four hours.

2Fit steering wheel, seat and any optional equipment.

3 Adjust cutting unit:

Adjust lift springs (effective weight of cutting unit should be 12-15kg / 26.5-33 lb).

Adjust cutting unit so that rear edge is about 2-4 mm / 1/8” higher than front edge.

Adjust cutting unit height setting so that cutting height limit is 5 mm / 3/16” above the frame of the unit at the lowest cutting height.

4 Check that the right amount of oil is in the engine.

5 Check that the right amount of oil is in the transmission. (Not Rider 11).

6 Check and adjust tyre pressure (60 Kpa, 0.6 bar).

7 Connect battery.

8 Fill with fuel and start engine.

9Check that machine does not move in neutral.

10 Check:

Forward drive.

Reverse drive.

Operation of blades.

Seat safety switch.

Lif lever safety switch.

Safety switch for the hydrostat pedals/neutral position.

Check that engine revs max. 2950 rpm.

11 Tell customer about:

Needs and beneﬁts of following the service schedule.

Servicing and the inﬂuence of this journal on the second-hand value of the machine.

Range of applications for BioClip.

Complete proof of sale etc.

Pre-delivery service carried out. No outstanding problems. Certiﬁed:

Date, mileage, stamp, signature

After the ﬁrst 5 hours

1 Change engine oil

English – 5

Image 5

Husqvarna 16 AWD, 13 C, 16 C, 11 C manual Service journal, Pre-delivery service, After the ﬁrst 5 hours

Contents

Rider 13 C Rider 11 CRider 16 AWD Rider 16 CContents CONTENTSCONTENTS Service journalDear Customer INTRODUCTIONDriving and transport on public roads TowingINTRODUCTION Good serviceSerial Number After the ﬁrst 5 hours Service journalPre-delivery service Symbols KEY TO SYMBOLSDrive very slowly if no cutting unit is ﬁtted Starting instructions KEY TO SYMBOLSCheck the engine’s oil level Check the hydrostat’s oil level Lift up the cutting unit Apply and lock the parking brakeSafety instructions SAFETY INSTRUCTIONSInsure your Rider General useThis is what you do Driving on slopesWARNING! You must use approved personal IMPORTANT INFORMATIONWARNING! The battery contains lead and MaintenanceChildren WARNING! The engine and the exhaustIMPORTANT INFORMATION TransportSAFETY INSTRUCTIONS Location of the controls WHAT IS WHAT?Presentation PRESENTATIONClutch pedal, Rider 11 C Brake pedal / Parking brakeExercise care and refuel outdoors see safety instructions Cutting height adjustment leverCutting unit Lifting lever for the cutting unitRelease lever Rider 16 AWD Release lever Rider 13 C, Rider 16 CClutch control, rear axle Clutch control, front axleBefore starting DrivingStart the engine IMPORTANT INFORMATIONConnecting the jump leads Starting the engine with a weak batteryRemove the cables in the reverse order WARNING! Never run the engine indoors, inCutting tips Driving the Rider2 For Rider 13 C, Rider 16 AWD and Rider 16 C 3 For Rider 11 CStop the engine Starting on a slope, manual gearbox, Rider 11 CWARNING! Do not use the machine on DrivingMaintenance schedule MaintenanceMaintenance interval The engine is switched off The ignition key is removedChecking and adjusting the steering wires CleaningRemoving of the machine hoods Engine coverAdjusting the parking brake Rider 13 C, Rider 16 C Adjusting the brake Rider 11 CWARNING! A poorly adjusted brake can Checking the brake Rider 11 CAdjusting the throttle wire Adjusting the parking brake Rider 16 AWDWARNING! A poorly adjusted parking brake Replacing the air ﬁlterChecking the fuel pump’s air ﬁlter Replacement of fuel ﬁlterChecking the tyre pressure MaintenanceWARNING! Procedures on contact with acid Check the level of the battery acidIgnition system FusesMaintenance Check the safety systemEnglish MaintenanceRider 13 C, Rider 16 C Rider 16 AWD Checking and adjustment of the cutting unit’s ground pressure Adjusting the parallelism of the cutting unitwhen the engine is running. Mind your ﬁngers Checking the engine’s cooling air intakeMaintenance Service position for the cutting unitPlacing in the service position Checking the blades Restoring from service positionRemoving the BioClip plug WARNING! If the blades are crackedChecking the engine’s oil level LubricationReplacing the engine oil WARNING! Engine oil can be very hot if it isLubrication Rider 11 C Lubricating the belt adjusterGeneral lubrication Rider 16 AWDProcedure Troubleshooting scheduleProblem Storage ServiceWinter storage GuardDimensions TECHNICAL DATARider 11 C EngineTECHNICAL DATA Rider 13 CDimensions Rider 16 AWDElectrical system Rider 16 CTECHNICAL DATA DimensionsTECHNICAL DATA ´z+S!¶6¶¨ 38 - English ´z+S!¶6¶¨EC-declaration of conformity Applies to Europe only Page 1151019-26 ´z+S!¶6¶¨ ´z+S!¶6¶¨