Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna 16 C, 13 C Contents, Introduction, Service journal, Key To Symbols, Safety Instructions

Models: 11 C 16 C 16 AWD 13 C

1 40

Download 40 pages 23.12 Kb

Page 2

CONTENTS

CONTENTS

Contents
CONTENTS
Contents	2
INTRODUCTION
Dear Customer,	3
Driving and transport on public roads	3
Towing	3
Use	3
Good service	4
Serial Number	4
Service journal
Pre-delivery service	5
After the ﬁrst 5 hours	5
KEY TO SYMBOLS
Symbols	6
SAFETY INSTRUCTIONS
Safety instructions	8
Driving on slopes	9
Children	10
Maintenance	10
Transport	11
WHAT IS WHAT?
Location of the controls	12
PRESENTATION
Presentation	13
Cutting unit	14
Lifting lever for the cutting unit	14
Cutting height adjustment lever	14
Seat	14
Fuelling	14
Release lever	15
Release lever	15
Driving
Before starting	16
Start the engine	16
Starting the engine with a weak battery	17
Driving the Rider	18
Cutting tips	18
Starting on a slope, manual gearbox, Rider 11 C	19
Stop the engine	19
Maintenance
Maintenance schedule	20
Cleaning	21
Removing of the machine hoods	21
Checking and adjusting the steering wires	21
Checking the brake, Rider 11 C	22
Adjusting the brake	22
Adjusting the parking brake	22
Adjusting the parking brake	23
Adjusting the throttle wire	23
Replacing the air ﬁlter	23
Replacement of fuel ﬁlter	24
Checking the fuel pump’s air ﬁlter	24
Checking the tyre pressure	24
Check the level of the battery acid	25
Ignition system	25
2 – English

Fuses	25
Check the safety system	26
Checking the engine’s cooling air intake	28
Checking and adjustment of the cutting unit’s ground
pressure	28
Checking the cutting unit’s parallelism	28
Adjusting the parallelism of the cutting unit	28
Service position for the cutting unit	29
Checking the blades	30
Removing the BioClip plug	30
Lubrication
Checking the engine’s oil level	31
Replacing the engine oil	31
Checking the oil level in the transmission on Rider 13 C,
Rider 16 AWD and Rider 16 C	31
Lubricating the belt adjuster	32
Lubrication, Rider 11 C	32
General lubrication	32
Troubleshooting schedule
Storage
Winter storage	34
Guard	34
Service	34
TECHNICAL DATA
EC-declaration of conformity	38

Image 2

Husqvarna 16 C Contents, Introduction, Service journal, Key To Symbols, Safety Instructions, What Is What?, Presentation

Contents

Rider 16 AWD Rider 11 CRider 13 C Rider 16 CCONTENTS CONTENTSContents Service journalDriving and transport on public roads INTRODUCTIONDear Customer TowingINTRODUCTION Good serviceSerial Number After the ﬁrst 5 hours Service journalPre-delivery service KEY TO SYMBOLS SymbolsCheck the engine’s oil level Check the hydrostat’s oil level KEY TO SYMBOLSDrive very slowly if no cutting unit is ﬁtted Starting instructions Lift up the cutting unit Apply and lock the parking brakeInsure your Rider SAFETY INSTRUCTIONSSafety instructions General useWARNING! You must use approved personal Driving on slopesThis is what you do IMPORTANT INFORMATIONChildren MaintenanceWARNING! The battery contains lead and WARNING! The engine and the exhaustIMPORTANT INFORMATION TransportSAFETY INSTRUCTIONS WHAT IS WHAT? Location of the controlsClutch pedal, Rider 11 C PRESENTATIONPresentation Brake pedal / Parking brakeCutting unit Cutting height adjustment leverExercise care and refuel outdoors see safety instructions Lifting lever for the cutting unitClutch control, rear axle Release lever Rider 13 C, Rider 16 CRelease lever Rider 16 AWD Clutch control, front axleStart the engine DrivingBefore starting IMPORTANT INFORMATIONRemove the cables in the reverse order Starting the engine with a weak batteryConnecting the jump leads WARNING! Never run the engine indoors, in2 For Rider 13 C, Rider 16 AWD and Rider 16 C Driving the RiderCutting tips 3 For Rider 11 CWARNING! Do not use the machine on Starting on a slope, manual gearbox, Rider 11 CStop the engine DrivingMaintenance interval MaintenanceMaintenance schedule The engine is switched off The ignition key is removedRemoving of the machine hoods CleaningChecking and adjusting the steering wires Engine coverWARNING! A poorly adjusted brake can Adjusting the brake Rider 11 CAdjusting the parking brake Rider 13 C, Rider 16 C Checking the brake Rider 11 CWARNING! A poorly adjusted parking brake Adjusting the parking brake Rider 16 AWDAdjusting the throttle wire Replacing the air ﬁlterChecking the tyre pressure Replacement of fuel ﬁlterChecking the fuel pump’s air ﬁlter MaintenanceIgnition system Check the level of the battery acidWARNING! Procedures on contact with acid FusesCheck the safety system MaintenanceEnglish MaintenanceRider 13 C, Rider 16 C Rider 16 AWD when the engine is running. Mind your ﬁngers Adjusting the parallelism of the cutting unitChecking and adjustment of the cutting unit’s ground pressure Checking the engine’s cooling air intakeMaintenance Service position for the cutting unitPlacing in the service position Removing the BioClip plug Restoring from service positionChecking the blades WARNING! If the blades are crackedReplacing the engine oil LubricationChecking the engine’s oil level WARNING! Engine oil can be very hot if it isGeneral lubrication Lubricating the belt adjusterLubrication Rider 11 C Rider 16 AWDProcedure Troubleshooting scheduleProblem Winter storage ServiceStorage GuardRider 11 C TECHNICAL DATADimensions EngineDimensions Rider 13 CTECHNICAL DATA Rider 16 AWDTECHNICAL DATA Rider 16 CElectrical system DimensionsTECHNICAL DATA ´z+S!¶6¶¨ 38 - English ´z+S!¶6¶¨EC-declaration of conformity Applies to Europe only Page ´z+S!¶6¶¨ ´z+S!¶6¶¨ 1151019-26