American Standard 2776.XXXW Series installation instructions General Installation Information

CADET™ 5 x 32

INTEGRAL APRON WITH REMOVABLE ACCESS PANEL HIGH GLOSS ACRYLIC SHOWN LESS ALL FITTINGS

2776.XXXW SERIES

WHIRLPOOL/BATHING POOL

INSTALLATION INSTRUCTIONS

				59-7/8
	12			(1521mm)
7-3/4	(305mm)				WATER
					RETENTION
(197mm)
					FLANGE
3/4
					(3 SIDES)
(19mm)
FINISHED
SEE FITTING WALL
SPECS FOR						14-3/4
DIMENSIONS
						(375mm)
			9
	(229 mm)
32						ON/OFF
					PUMP	SWITCH
(813mm)		CUTOUT IN FLOOR
		FOR DRAIN
C/L OF	2-3/8				(2) AIR VALVES	ACCESS TO PUMP/MOTOR
SUPPLIES	(60mm)			(8) JETS		THROUGH REMOVABLE
						FRONT ACCESS PANEL
	C/L OF DRAIN				C/L OF
					SHOWER ARM
					FINISHED
OPTIONAL TO					WALL
FINISHED FLOOR	7/8 WATER				C/L OF
USUALLY BETWEEN
65 & 78	RETENTION				VALVES
(1651 & 1981mm)	FLANGE
	(3 SIDES)			12	C/L OF
	C/L OF
			(305mm) OPT.		SPOUT
	OVERFLOW
				4
	2-3/4				■ LEVELING STRINGER
				(102 mm)
	(70mm)				NOT FOR SUPPORT
TOP OF						UNDERSIDE
DECK	20					OF DECK
	(508mm)					19-3/4
	ROUGH					(502mm)
	FLOOR
	BATH			1-1/2 N.P.T.M.
	SUPPORT			THREADS	2-3/4
	MATERIAL	1-1/2 O.D.TAILPIECE			(70mm)
					4-5/8
					(117mm)
GENERAL SPECIFICATIONS FOR 2776 WHIRLPOOL
INSTALLED SIZE				59-7/8 x 32 x 20 (1521 x 813 x 508mm)
WEIGHT					115 Lbs. (52 Kg.)
WEIGHT w/WATER					574 Lbs. (258 Kg.)
GAL. TO OVERFLOW					55 Gal. (208 L.)
WHIRLPOOL MIN. OPERATING VOL.					45 Gal. (171 L.)
BATHING WELL AT SUMP					20 x 40 (508 x 1016mm)
BATHING WELL AT RIM				26 x 53-1/2 (660 x 1359mm)
WATER DEPTH TO OVERFLOW					14-1/2 (368mm)
FLOOR LOADING				43 Lbs./Sq.Ft. (208 Kgs./Sq.m)
(PROJECTED AREA)
PTS.						20.8
CUBE (FT3)						35.3
WHIRLPOOL ELECTRICAL SPECIFICATIONS
SYSTEM I PUMP					1.1 HP, 9.9 AMPS,120V.

GENERAL INSTALLATION INFORMATION

THANK YOU...

for selecting an American Standard bath. Your new bath is shipped to you after careful inspection. The whirlpool version is completely assembled with pump, motor, and system piping. All you need to finish the installation are your selected fittings and electrical connections for a whirlpool.

To insure maximum performance and pleasure from this product, please follow the instructions and cautions.

List of Required Components (not included):

• Drain 1583.470* • Bath Filler* * see your American Standard Distributor

List of Required Tools and Supplies:

Tools		Supplies
•	Level	•	Nails
•	Tape Measure	•	Putty
•	Pipe Wrench	•	Caulking (waterproof)
•	Slip Joint Pliers	•	1 x 3 or 2 x 2
•	Screw Driver		Stringers
•	Standard	•	Drop Cloth
	Woodworking Tools	•	15 amp GFI
•	Personal Safety		Outlet
	Equipment	•	Cement, Plaster,
•	Caulking Gun		Grout

GENERAL INSTALLATION INFORMATION

Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor immediately.

After inspection and during installation, protect the bath from construction damage. Before installation, and before enclosing with wallboard, tile, etc., water test the unit and check for leaks.

If a whirlpool, do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump, motor, or piping system.

Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and enclosing materials are provided by others.

BATH MAY ONLY BE INSTALLED IN A RECESS TYPE INSTALLATION.	IMPORTANT:
	Water test unit before installation and enclosure!

LOCATE STUDS AS REQUIRED. INSURE ROUGH DIMENSIONS ARE PROPER, PLUMB AND SQUARE. FOR WHIRLPOOLS, ACCESS TO PUMP/MOTOR MAY BE MADE THROUGH ACCESS OPENING IN APRON PANEL. THE FOLLOWING PROCEDURE MUST BE USED FOR ALL INSTALLATIONS: LEVELING SUPPORT STRINGER SHOULD BE AS INDICATED. THIS BATH IS NOT SELF-SUPPORTING AND MUST BE SUPPORTED ALONG IT'S ENTIRE BOTTOM. SUPPORT WITH MORTAR OR GROUT.

POSITION BATHTUB/WHIRLPOOL WITHIN THE RECESS, CHECK LEVEL, FRONT TO BACK, SIDE TO SIDE, AND SHIM AS NECESSARY.

TO SECURE THE TUB TO WOOD STUDS USE DRYWALL SCREWS W/WASHERS OR ROOFING NAILS IMMEDIATELY ABOVE THE FLANGE OF THE TUB. TO SECURE THE TUB TO STEEL STUDS USE 4" DRYWALL SCREWS AND FLATWASHERS.

SEE PAGE 2 FOR COMPLETE INSTALLATION INFORMATION.

CAUTION: TAKE EXTRA CARE WHEN DRIVING NAILS OR SCREWS TO AVOID DAMAGING THE TUB.

THE TILE OR SIMILAR FINISHED FLOOR WILL BE BUTTED AGAINST THE BOTTOM OF THE TUB APRON, ALSO HOLDING THE TUB IN PLACE.

FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.

© American Standard Inc. 2003

752561-100 Rev. DAll product names listed herein are trademarks of American Standard Inc. unless otherwise noted.