American Standard 2901.XXXW installation instructions Installation Instructions, Savona, Tools

SAVONA™

HIGH GLOSS ACRYLIC SHOWN LESS ALL FITTINGS

2901.XXXW

SERIES WHIRLPOOL

INSTALLATION INSTRUCTIONS

905mm (35-5/8)

552mm

1105mm (21-3/4) (43-1/2)

305mm

(12)140mm (5-1/2)

1810mm	19mm
(71-1/4)
SAFE-T-HEATER	(3/4)
	TYP.
REMOVABLE
BLANK	ON/OFF
	SWITCH
	PUMP
	OUTLINE OF
C/L	1772mm X
	1067mm
	(69-3/4 X 42)
	CUTOUT
178mm
(7)

THANK YOU...

for selecting an American Standard bath. Your new bath is shipped to you after careful inspection. The whirlpool version is completely assembled with pump, motor, and system piping. All you need to finish the installation are your selected fittings and electrical connections for a whirlpool.

To insure maximum performance and pleasure from this product, please follow the instructions and cautions.

C/L OF 1-1/2 O.D.

DRAIN OUTLET

●RECOMMENDED FITTING LOCATION

64 X 279mm (2-1/2 X 11)

	38mm
51mm	(1-1/2)
(2)

INTEGRAL

FEET

229mm X 305mm (9 X 12) FLOOR CUTOUT

C/L OF OVERFLOW

89mm (3-1/2)

PROVIDE ACCESS

TO PUMP FOR SERVICE

ON ALL INSTALLATIONS

■LEVELING STRINGER NOT FOR SUPPORT

559mm

(22)

508mm

(20)

List of Optional Components (not included):

•Safe-T-Heater 9075.120*

•Tile Bead Kit 751755-100*

* see your American Standard Distributor

List of Required Components (not included):

• Drain 1583.470*

• Bath Filler*

44 mm		ROUGH
(1-3/4)	89 mm	FLOOR
	(3-1/2)

	1-1/2 O.D. TAILPIECE			1-1/2 N.P.T.M.
				THREADS
GENERAL SPECIFICATIONS FOR 2901 WHIRLPOOL
INSTALLED SIZE		71-1/4 x 43-1/2 x 22 In.(1810 x 1105 x 559mm)
WEIGHT					152 Lbs. (68 Kg.)
WEIGHT w/WATER					936 Lbs. (421 Kg.)
GAL. TO OVERFLOW					94 Gal. (356 L)
WHIRLPOOL MIN. OPERATING VOL.					86 Gal.(326 L)
BATHING WELL AT SUMP					44 x 28 In. (1118 x 711mm)
BATHING WELL AT RIM			67-1/2 x 33 In. (1715 x 838mm)
WATER DEPTH TO OVERFLOW					16-1/4 In. (413mm)
FLOOR LOADING			43 Lbs./Sq.Ft. (211 Kgs./Sq.m)
(PROJECTED AREA)
PTS.			27.8
CUBE (FT3)						61.5
	WHIRLPOOL ELECTRICAL SPECIFICATIONS
SYSTEM II PUMP					2.1 HP, 15.6 AMPS, 120V.

GENERAL INSTALLATION INFORMATION

* see your American Standard Distributor

List of Required Tools and Supplies:

Tools		Supplies
•	Level	•	Nails
•	Tape Measure	•	Putty
•	Pipe Wrench	•	Caulking (waterproof)
•	Slip Joint Pliers	•	1 x 3 or 2 x 2
•	Screw Driver		Stringers
•	Standard	•	Drop Cloth
	Woodworking Tools	•	20 amp GFI
•	Personal Safety		Outlet
	Equipment	•	Cement, Plaster,
•	Caulking Gun		Grout

Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor immediately.

After inspection and during installation, protect the bath from construction damage. After installation, and before enclosing with wallboard, tile, etc., water test the unit and check for leaks.

Do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump, motor, or piping system.

Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and enclosing materials are provided by others. Check for availability of optional American Standard wall tiling bead (required for recess installations).

Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.

WARNING! Do not lift whirlpool by the piping harness at any time.

FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.

© American Standard Inc. 2003

752459-100 REV.FAll product names listed herein are trademarks of American Standard Inc. unless otherwise noted.