11 INSTALL HANDLES |
|
|
Push ADAPTER (1) on VALVE STEM (2), so that the hole of the |
|
|
ADAPTER (1) without a spline is facing up. See figure "A". Tighten |
| THREAD ON |
STEM SCREW (3) to secure ADAPTER (1). |
| |
| TO DECK | |
Find correct position of LEVER HANDLE ASSEMBLY (4) by adjusting | 4 | ADAPTER |
|
| |
male teeth on ADAPTER (1) to female teeth in HANDLE (4). | TOP |
|
|
| |
Thread LEVER HANDLE ASSEMBLY (4) onto DECK ADAPTER (5) |
| 1 |
until snug against mounting surface. |
| |
| 3 | |
Figure "A" |
| |
|
| 2 |
SPLINE END DOWN |
| 5 |
12 TEST INSTALLED FITTING |
| OUTLINE OF BIDET |
|
|
With HANDLES (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks.
Operate both HANDLES (1) to flush water |
|
lines thoroughly. | 1 |
| |
Rotate TRANSFER VALVE (5) from rim wash to |
|
spray several times to check operation. |
|
3
1
13 CHECK DRAIN CONNECTIONS |
|
|
Pull up | 4 |
|
that DRAIN STOPPER (4) makes a good seal and retains | 2 | |
water in Bidet. If STOPPER (4) does not seal properly, |
| |
|
|
please refer to “Troubleshooting Guide” in these instructions. | SPRAY |
| |
Push |
|
connections and "P" trap for leaks. Tighten |
|
if necessary. |
|
2
14 CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER.DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE.
15 | SERVICE |
|
|
|
|
| ||||
|
|
|
|
| ||||||
|
|
| HANDLE | |||||||
|
| To change direction of handle rotation, |
|
|
| ASSEMBLY | ||||
|
|
|
|
|
|
| ||||
|
| proceed as follows: | UNTHREAD | |||||||
|
|
|
| Turn valve to OFF position. Unthread HANDLE | ||||||
|
|
|
| |||||||
|
|
|
|
|
|
|
|
| ||
|
|
|
| BASE (1) from DECK ADAPTER (2). |
|
|
|
|
| |
|
|
|
| Pull HANDLE ASSEMBLY off VALVE STEM (3). | 1 |
|
|
|
| |
|
|
|
|
|
|
|
| |||
|
|
|
| Remove SPRING CLIP (4). Lift STOP WASHER (5), |
|
|
|
|
| |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| ||
turn 90˚ and replace. Replace SPRING CLIP (4).
Find correct position of HANDLE ASSEMBLY by adjusting 90˚ | 3 | |
male teeth on VALVE STEM (3) to female teeth in HANDLE. | 5 | |
Thread HANDLE ASSEMBLY onto DECK ADAPTER (2) | 4 | |
until snug against mounting surface. |
| |
If spout drips, operate handles several times from | 2 | |
OFF to ON position. Do not force - handles turn | ||
| ||
only 90˚ . | M968845 Rev . 1 . 2 | |
|
4
