American Standard 6060.028WC dimensions Cadenza Whirlpool, High Gloss, Revised 2/08

CADENZA™

WHIRLPOOL

HIGH GLOSS

1949mm

(76-3/4 REF.)

975mm

(38-3/8)

1661mm (65-3/8)

OUTLINE OF	C/L	1384mm
CUTOUT		(54	1605mm
		-
			(63
		1/2)
			-
			3/16)

SEAT AREA

PUMP

178mm x 381mm (7 x 15) CUTOUT

PROVIDE ACCESS TO PUMP FOR SERVICE ON ALL INSTALLATIONS NOTE: APRON ASSEMBLY WILL PROVIDE REQUIRED ACCESS FOR SERVICING

346mm					ON/OFF SWITCH
(13-5/8)
				RECOMMENDED FITTING
143mm		254mm		LOCATION 64 X 381mm (2-1/2 X 15)
	C/L OF
(5-5/8)
		(10)
	DRAIN
			114mm
					LEVELING STRINGER
C/L OF OVERFLOW			(4-1/2)
					NOT FOR SUPPORT
89mm
(3-1/2)			E-Z-Install™ HEATER
83mm					495mm
					(19-1/2)
(3-1/4)
				51mm
				(2)	546mm
38mm					(21-1/2)
(1-1/2)				INTEGRAL FEET
				SUPPORT
		1-1/2 N.P.T. THREAD		ROUGH FLOOR
		1-1/2 O.D. TAILPIECE
		GENERAL SPECIFICATIONS FOR 6060 WHIRLPOOL
	INSTALLED SIZE		76-3/4 x 65-3/8 x 21-1/2 In. (1949 x 1661 x 546mm)
	WEIGHT			105 Lbs. (48 Kg.)
	WEIGHT w/WATER			822 Lbs. (370 Kg.)
	GAL. TO OVERFLOW				86 Gal. (326 L)
	WHIRLPOOL MIN. OPERATING VOL.				71 Gal. (269 L)
	BATHING WELL AT SUMP			45 x 40 In. (1143 x 1016mm)
	BATHING WELL AT RIM			49 x 43 In. (1245 x 1092mm)
	WATER DEPTH TO OVERFLOW			15-3/8 In. (391mm)
	FLOOR LOADING			24 Lbs./Sq.Ft. (114 Kgs./Sq.m)
	(PROJECTED AREA)
	PTS.				41.7
	CUBE (FT3)				68.4
		WHIRLPOOL ELECTRICAL SPECIFICATIONS
	SYSTEM II PUMP			2.1 HP, 15.6 AMPS,120V.

NOTES:

BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND OR PENINSULA TYPE INSTALLATION. SUP- PORT OF BATH BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. SUPPORT AND ENCLOSING MATERIAL BY OTHERS.

■REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION. OPTIONAL 2-WALL TILING BEAD KIT No.751755-100 MUST BE ORDERED SEPARATELY.

▲CUTOUT TEMPLATE PROVIDED IN SHIPPING BOX. MAY BE REQUESTED SEPARATELY. PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS.

●FITTINGS NOT INCLUDED, MUST BE ORDERED SEPARATELY.

●IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR INTERFERENCE WITH CIRCULATING SYSTEM PIPING, DRAIN OVERFLOW, AND APRON INSTALLATION. MOUNTING HOLES DRILLED BY INSTALLER.

IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1 These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaflet.

	H40
© 2008 AS America Inc.		Revised 2/08