American Standard 6060EC dimensions Cadenza Elite Corner, Whirlpools By American Standard, 3/16

CADENZA ELITE™ CORNER

WHIRLPOOLS BY AMERICAN STANDARD

HIGH GLOSS ACRYLIC

1949mm

(76-3/4 REF.)

975mm (38-3/8)

OUTLINE OF	C/L
CUTOUT
	SEAT AREA

1661mm

(65-3/8)

178mm x 381mm

(7 x 15) CUTOUT

346mm

(13-5/8)

1384mm
(54	1605mm
-
	(63
1/2)
	-
	3/16)

PUMP

ACCESS FOR SERVICING

NOTE: APRON ASSEMBLY WILL PROVIDE REQUIRED

ON ALL INSTALLATIONS

PROVIDE ACCESS TO PUMP FOR SERVICE

ON/OFF SWITCH

143mm	C/L OF	254mm
(5-5/8)
		(10)
	DRAIN
		114mm
C/L OF OVERFLOW		(4-1/2)
89mm
(3-1/2)		E-Z INSTALL WHIRLPOOL
		HEATER
83mm
(3-1/4)
38mm
(1-1/2)
		1-1/2 N.P.T. THREAD
		1-1/2 O.D. TAILPIECE

● RECOMMENDED FITTING LOCATION 64 X 381mm (2-1/2 X 15)

■LEVELING STRINGER NOT FOR SUPPORT

495mm (19-1/2)

51mm

(2)546mm (21-1/2)

INTEGRAL FEET

SUPPORT

ROUGH FLOOR

NOTES:

GENERAL SPECIFICATIONS FOR 6060E WHIRLPOOL

INSTALLED SIZE		76-3/4 x 65-3/8 x 21-1/2 In. (1949 x 1661 x 546mm)
WEIGHT						105 Lbs. (48 Kg.)
WEIGHT w/WATER						822 Lbs. (370 Kg.)
GAL. TO OVERFLOW							86 Gal. (326 L)
WHIRLPOOL MIN. OPERATING VOL.							71 Gal. (269 L)
BATHING WELL AT SUMP				45 x 40 In. (1143 x 1016mm)
BATHING WELL AT RIM				49 x 43 In. (1245 x 1092mm)
WATER DEPTH TO OVERFLOW						15-3/8 In. (391mm)
FLOOR LOADING			24 Lbs./Sq.Ft. (114 Kgs./Sq.m)
(PROJECTED AREA)
PTS.								41.7
CUBE (FT3)								68.4
	WHIRLPOOL ELECTRICAL SPECIFICATIONS
PUMP					2.1 HP, 14.4 AMPS,120V.
E-Z INSTALL WHIRLPOOL HEATER						12.0 AMPS,120V.

BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND OR PENINSULA TYPE INSTALLATION. SUPPORT OF BATH BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. SUPPORT AND ENCLOSING MATERIAL BY OTHERS.

■REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.

OPTIONAL 2-WALL TILING BEAD KIT No.TILE-BEAD MUST BE ORDERED SEPARATELY.

▲CUTOUT TEMPLATE PROVIDED IN SHIPPING BOX. MAY BE REQUESTED SEPARATELY. PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS.

●FITTINGS NOT INCLUDED, MUST BE ORDERED SEPARATELY.

●IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR INTERFERENCE WITH CIRCULATING SYSTEM PIPING, DRAIN OVERFLOW, AND APRON INSTALLATION. MOUNTING HOLES DRILLED BY INSTALLER.

IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1

These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaflet.

© 2003 American Standard Inc.